User manual PANASONIC AW-RP50N BASIC MANUAL

[. . . ] Operating Instructions <Basics> Remote Camera Controller Model No. AW-RP50N Before operating this product, please read the instructions carefully and save this manual for future use. For instructions on how to operate this Remote Camera Controller and how to establish its settings, refer to the "Operations and Settings" manual (PDF file) which can be found on the CD-ROM supplied with the camera. 3TR006515BAA Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER TO SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. FCC Note: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] The OTAF (one-touch auto focus) takes effect for remote cameras which are equipped with the OTAF function. Adjust the zoom. Use the ZOOM button to adjust the lens zoom. When the TELE side is pressed, the zoom is set to the telephoto mode; when the WIDE side is pressed, it is set to the wide-angle mode. 7 Turn off the unit's power. Set the POWER switch to the OFF position. The unit's power is turned off, and the POWER indicator goes off. Even when the unit's power is turned off, the power of the connected remote cameras does not go off. 1, 7 F1 F2 POWER ALARM F1 CAMERA OSD 1 MENU PAGE GAIN/PED 2 R/B GAIN 3 R/B PED 4 AWB/ABB 5 SHUTTER F2 EXIT 6 STORE DELETE DETAIL 7 8 9 10 SYSTEM SETUP SCENE/MODE CAMERA PRESET MEMORY / MENU USER1 USER2 5 IRIS AUTO 1 2 3 4 5 PT ACTIVE CAMERA STATUS / SELECTION 4 TELE ZOOM WIDE AUTO 3 FOCUS/PUSH OTAF LOW HI PTZ/FOCUS SPEED PAN/TILT 6 2 For detailed operations, refer to the Operating Instructions -- <Operations and Settings>. 16 Basic operations for the menus 1 2 Set the MENU button to ON. Press the MENU button and light its indicator. Press the EXIT button to return the menu to its previous hierarchical level. When the down arrow "" is displayed for a setting item, it means that the value shown will be entered and the setting reflected when the F1 dial or F2 dial is pressed. 1. GROUP SELECT 1 When the down arrow "" is not displayed for a setting item, it means that the value shown will be entered and the setting reflected when the F1 dial or F2 dial is turned. RGAIN BGAIN : : ±0 ±0 F1 dial F2 dial Select the target menu. Press the corresponding PRESET MEMORY/ MENU button, and light its indicator. For details on the menus assigned to these buttons, refer to "Table of menu items" (<Operations and Settings> Operating Instructions). The selected menu is displayed on the LCD panel. 3 Change the settings using the F1 dial and F2 dial. Use the F1 dial and F2 dial to select the menus and change the settings. Use the F1 dial for operations involving the items displayed on the top line of the LCD panel. Use the F2 dial for operations involving the items displayed on the bottom line of the LCD panel. F1 F2 POWER ALARM F1 CAMERA OSD 3 1 MENU PAGE STORE DELETE 1 GAIN/PED 2 R/B GAIN 3 R/B PED 4 AWB/ABB 5 SHUTTER F2 EXIT 6 DETAIL 7 8 9 10 SYSTEM SETUP SCENE/MODE CAMERA PRESET MEMORY / MENU USER1 USER2 1 IRIS AUTO 2 3 4 5 PT ACTIVE CAMERA STATUS / SELECTION AUTO TELE ZOOM WIDE FOCUS/PUSH OTAF LOW HI PTZ/FOCUS SPEED PAN/TILT 2 For detailed operations, refer to the Operating Instructions -- <Operations and Settings>. 17 Network settings This section describes how the unit's network are set. 5 Turn the F1 dial, and display the target setting item. 1. IP ADDRESS 192 168. 000. 009 Note Correct operation is not possible if the same IP address already exists in the same network. Set the IP addresses in such a way that they do not duplicate any existing IP addresses. Setting the unit The unit's settings are established using the [SYSTEM] menu. Set the IP address, subnet mask and default gateway. First, the basic menu operations will be described. 2. SUBNETMASK 255 255. 255. 000 3. GATEWAY 192 168. 000. 001 1 2 Set the MENU button to ON. Press the MENU button, and light its indicator. 4. MAC ADDRESS Set the PRESET MEMORY/MENU 10 button (SYSTEM) to ON. When the button is pressed and its indicator is lighted, the [SYSTEM] menu is displayed on the LCD panel. 6 Turn the F2 dial, and select the setting. 2. SUBNETMASK 255 255. 255. 000 [1]CAMERA CTL 7 Press the F2 dial, and change the setting. 2. SUBNETMASK 255. 255 255. 000 Input all the settings except for the MAC address in four blocks of numerals. When input advances to the last block and the F2 dial is pressed, the IP address is entered. 2. SUBNETMASK 255. 255. 255. 000 The MAC address is merely displayed -- it cannot be changed. 3 Turn the F1 dial, and display the [NETWORK] menu. [6]NETWORK 4 Press the F1 dial. 1. IP ADDRESS 192 168. 000. 009 Note In order for the settings to take effect, the unit must be restarted. Turn off the unit's power, and then turn it back on again. 18 Network settings Setting the IP address On the [SYSTEM] menu, select the [NETWORK] menu, and display [IP ADDRESS]. Then operate the F2 dial to set the IP address. Select a setting which will not duplicate the IP setting of another device. Setting the subnet mask On the [SYSTEM] menu, select the [NETWORK] menu, and display [SUBNETMASK]. Then operate the F2 dial to set the subnet mask. 1. IP ADDRESS 192 168. 000. 009 2. SUBNETMASK 255 255. 255. 000 If the subnet mask is incorrect, the following message is displayed on the LCD panel. [. . . ] Operate the PAN/TILT lever, and check whether the camera whose camera number is to be changed is being moved. The IP address that can be selected is the IP address of the camera number which has been set for "Network" for the [CAM1] to [CAM100] item of [CAMERA CTL] on the [SYSTEM] menu. On the [SYSTEM] menu, select [SW IP ADR], and display [IP:SW]. Then change the IP address. Clearing the IP address control tables All the IP address control tables which have been set can be cleared together. 1 On the [SYSTEM] menu, select [AUTO SETUP], and display [AUTO SETUP]. Then select "ALL CLEAR", and press the F2 dial to clear all the tables. 1. AUTO SETUP ALL CLEAR 3 Press the F2 dial to enter the IP address. The IP addresses for the camera number of the change destination and for the camera number of the change source are switched over. [. . . ]