User manual PANASONIC BB-HCS301A

[. . . ] DC IN PO WE R VID EO Operating Instructions IN AU UD DIO IO IN IN Network Camera Server Model No. BB-HCS301A Please read this manual before using and save this manual for future reference. Panasonic Network Camera Website: http://www. panasonic. com/netcam for customers in the USA or Puerto Rico Operating Instructions Main Features Motion-JPEG Conversion from Analog Camera Image When the analog camera is connected to this product, you can view the image from the Internet. Video Output Terminal and Local Audio Mode This product provides Video Output Terminal that allows you to output the video signal from Video Input Terminal and Local Audio Mode that allows you to output the audio signal from Audio Input Terminal. By cascading this product, the simultaneous accesses to the same video or audio can be increased (Up to 5). IPv6*1 Supported This product supports IPv6 (Internet Protocol Version 6), IPv6 was created to address the additional IP addresses that will be needed as the Internet continues to expand. Since this product also supports IPv4 that is currently used, it is "dual stack" design will seamlessly operate while IPv6 is phased in. [. . . ] (2) Click [Sounds, Speech, and Audio Devices] [Sounds and Audio Devices]. (3) Click the [Audio] tab, and click [Volume. . . ] in the Sound recording. (4) Confirm that the Microphone is checked, and adjust the volume bar. 72 Operating Instructions 2. Adjust the sensitivity of the local audio. (2) Select [Minimum], [Standard] or [Maximum] in the Sensitivity (see page 69). (3) Click [Save]. (2) Select [Minimum], [Standard] or [Maximum] in the Volume (see page 69). (3) Click [Save]. [For assistance, please call: 1-800-272-7033] 73 Operating Instructions 2. 12 Changing Authentication Setting and Administrator User Name and Password The Security: Administrator page allows you to change authentication, administrator user name and password. The authentication window is displayed, and allows the registered users to access this product. Notes · If you access this product for the first time, the window to set administrator user name and password is displayed. Make a note of the user name and password so that you will not forget them. · The user name and password should be secured at your own responsibility. ­ Set the user name and password as many characters as possible. IMPORTANT · It is important to limit access to this product by use of a unique User Name and a secret Password. Because this product is accessed through the Internet it is possible that this product could be accessed by unknown individuals, including those who are commonly known as "crackers" to whom you do not want to allow access. The use of a unique User Name and a Password known only to you will help insure that only authorized individuals are given access to this product. You have the option of proceeding without a User Name and Password, but it is strongly recommended that you utilize these protections. 1. Click [Administrator] on the Setup page. Set each parameter. · Clicking [Cancel] cancels your settings without saving changes. 74 Operating Instructions Setting General Authentication Description Authentication has 2 phases. · If you set [Permit access from guest users], this product does not display the authentication window in camera access. All guest users can view the image without user name and password. Note If you set [Permit access from guest users], [Login] tab is displayed at the top of the page. After you log in as an administrator (see page 77), you can access the Setup page and the Maintenance page. · If you set [Do not permit access from guest users], this product displays authentication window in camera access. Users must enter the user name and password. User Name (6 to 15 characters): Enter the user name. Password (6 to 15 characters): Enter the password. User Name/ Password · · Note · · The password must be different from the user name. [. . . ] Follow the instructions below to insert the SD memory card into this product. How to Insert or Remove the SD Memory Card 1. Confirm that the SD memory card label faces up, and insert the card shown as below. 2. Push the card with your finger until it clicks. To remove the card, push its center, then pull it straight towards you. PO WE R PO WE R · Ensure that recording has been stopped, before removing the card (see page 114). [. . . ]