User manual PANASONIC BMET500

[. . . ] Iris Camera Operating Instructions Model No. BM-ET500E DEUTSCH ACCEPT REJECT READY Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. ITALIANO ESPAÑOL FRANÇAIS ENGLISH ENGLISH VERSION We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives EEC/73/23 and EEC/89/336. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatiefve dokumenten, overeenkomstig de bepalingen van Richtlijnen 73/23/EEC en 89/336/EEC. Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i overensstemmelse med den følgende standarder eller andre normative dokumenter i følge bestemmelserne i direktivene 73/23/EEC og 89/336/EEC. Vi deklarerar härmed värt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är i överensstämmelse med standarddokument, eller andra normativa dokument som framstölls i Direktiv 73/23/EEC och 89/336/EEC. [. . . ] · Do the self-diagnostic test, when you open this unit door for maintenance, etc. The self-diagnostic test can be carried out by turning on a power supply. Read BM-ED500 Operating Instructions for turning on a power supply. 6 DOCUMENT CONVENTION These operating instructions use the following convention when describing the use and operation of this system. o Buzzer-level adjustment hole Adjusts the level of buzzer, which informs you of recognition/enrollment results. Refer to p. 13 for details on level adjustment. Note: Keep away from this hole except for qualified service personnel. 8 INSTALLATIONS AND CONNECTIONS WARNING The installation described in these figures should be made by qualified service personnel or trained system installers. Cautions: · This system must be installed within the protected promise in accordance with the International Electrotechnical Commission, and the local authorities having jurisdiction. · Attach this unit to a flat wall with the supplied mounting bracket. After the installation, secure the unit to prevent dropping. The unit can be mounted over the wall as described. Attach the anchor into the wall, and then attach the supplied mounting bracket to the anchor. (Refer to the figure in p. 12. ) The anchor bolt should meet the standards shown in the illustration. Remove the shipping lock as follows: 1 Locked Belt 2 (1) Remove the screw. (2) Insert the belt until it hits to the stop. 3 Unlocked (3) Bend the belt and secure it with the screw. · Take care not to drop the screw inside the unit. · You can use an M3 screw if you have lost this screw. 10 mm (2/5 in. ) or less Wall 3. You can remove the keys by taking off the two tamperproof screws (with the supplied screw driver tool) and lifting up the keyboard. The control cable should also be removed. 1 6 2 7 3 8 4 9 5 0 CANCEL ENTER Remove the screws. Mounting bracket 2 mm (2/25 in. ) (D) 1 2 3 4 5 CANCEL 9 4. Attach the unit to the mounting bracket. (1) Attach the mounting bracket to the wall. Video output cable and power cable * (from the control unit) (2) Remove the numeric keyboard. 1 2 3 4 Provide access for cables to be routed through the wall. 5 CANCEL Screw nut (M5) (3) Remove the shipping lock. (4) Attach the unit to the mounting bracket. Secure the unit and bracket with the screw nut, using an 8 mm (0. 03 in. ) socket driver. * Refer to the control unit's operating instructions for the specifications. 5. [. . . ] When you have mistaken the entry of ID or password "REJECT" will light up and the buzzer will beep. ACCEPT REJECT READY Lights up ACCEPT REJECT READY Caution: Avoid setting the following examples to your ID or password. · Public information such as your birthday or phone number · Repeated numerics such as 1111 or 7777 · Sequential numerics such as 1234 or 7890 Note: The digit number differs depends on the system environment. When you have forgotten your ID or password, contact the system administrator. 15 ADDITIONAL SYSTEM COMPONENTS Control Unit BM-ED500 Administration Software BMES500E Administration Software BM-ES500E This product is necessary for administering iris data, IDs, and passwords. This product is necessary for iris data recognition/enrollment and controlling an electric lock. 16 TROUBLESHOOTING Check to see the following before request for repair. If a trouble cannot be corrected even after checking and trying remedy, contact your dealer. Problem System does not power up. Check item The power of the control unit may be turned off. [. . . ]