User manual PANASONIC BT-LH1700

[. . . ] Operating Instructions LCD Video Monitor Model BT- P Before operating this product, please read the instructions carefully and save this manual for future use. S0805M1095 -H D Printed in Japan ENGLISH VQT0U69-1 For Your Safety CAUTION: In order to maintain adequate ventilation, do not install or place this unit in a bookcase, built-in cabinet or any other confined space. To prevent risk of electric shock or fire hazard due to overheating, ensure that curtains and any other materials do not obstruct the ventilation. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. CAUTION: This apparatus can be operated at a voltage in the range of 100 - 240 V AC. Voltages other than 120 V are not intended for U. S. A. g THIS EQUIPMENT MUST BE GROUNDED To ensure safe operation, the three-pin plug must be inserted only into a standard three-pin power outlet which is effectively grounded through normal household wiring. [. . . ] <VARICAM> VARICAM use <OTHER> When using other types than VARICAM Used to select the color temperature. <USER0­63> Adjustable settings 0­63 (color temperature around 3000K­9300K) <D93> Color temperature around 9300K <D65> Color temperature around 6500K <D56> Color temperature around 5600K <VAR1> WB adjustment mode*4 <VAR2> WB adjustment mode*4 <VAR3> WB adjustment mode*4 Used to select the width of the sharpness edge. <HIGH> Thin edge <LOW> Thick edge Used to set the sharpness in the horizontal direction. When adjusting, the item display moves to the lower part of the screen. Used to set the sharpness in the vertical direction. When adjusting, the item display moves to the lower part of the screen. <MODE2> Within Field <MODE1> Normal mode COLOR TEMP. SHARPNESS MODE*2 SHARPNESS H*2 <HIGH>*3 <LOW> <0­30> *3 SHARPNESS V*2 <0­30> *3 I-P MODE*2 MONO *2 <MODE2> <MODE1> <OFF> <ON> Used to switch between color and monochrome (MONO). <OFF> Color <ON> Monochrome * When this is ON, the picture adjusting knob [CHROMA] setting is fixed at 0. If an Anamo lens has been used on the camera, and input through SDI 720/60P, 59. 94P, the picture is resized to Anamo size magnification. (a vertically compressed signal can be amplified vertically and corrected when it is displayed. ) Used for setting the aspect ratio settings when using SD signal input. <4:3> 4:3 display <16:9> 16:9 display Used to set under-scan and normal display. <NORMAL>Normal display <UNDER>Under-scan <OFF> This makes a fluid and smooth contrast obtainable. This is especially effective for continuously changing the contrast of the source signal or CG signal when the S/N is very high. Depending on the camera, this mode can be especially effective for dark scenes. We recommend leaving this setting "ON" under normal conditions. ANAMO*2 <OFF> <ON> SD ASPECT*2 <4:3> <16:9> <NORMAL> <UNDER> <OFF> <ON> SCAN*2 NOISE WIPE*2 *1 Even if FILM gamma is changed during 2 screen display, only the main window is set, and the changes are not reflected in the sub window. *2 When "RGB-COMP. " is selected in "YPBPR/RGB" in the "INPUT SELECT" menu ( page 21), this does not operate. *3 The following sharpness values can each be set, 1) VIDEO system input line (VIDEO, Y/C)(Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0) 2) any other input line's HD (Factory settings are SHARPNESS MODE : HIGH, SHARPNESS H/V : 0) 3) any other input line's SD (Factory settings are SHARPNESS MODE : LOW, SHARPNESS H/V : 0) and the setting values for the selected input signal from within this group is displayed. The adjustment status is displayed in the bottom right when selected. *4 When "VAR1", "VAR2" or "VAR3" is selected, the monitor switches to WB adjustment mode ( page 17). *5 When selecting USER0­63 1) Push [ENTER] (USER changes to blue). 2) Select 0­63 with [ , ], and push [ENTER]. 16 Main Menu (continued) g WB adjustment mode You can adjust "WHITE BALANCE VAR1" ­ "WHITE BALANCE VAR3" (WB) by selecting "VAR1" ­ "VAR3" in "COLOR TEMP. " in the "VIDEO CONFIG" menu. The underlined values are factory preset setting values. [. . . ] Doing so would cause the surface of the monitor to become discolored, and cause paint to peel. · Do not spray cleansers directly onto the monitor. Water or similar substances getting inside the monitor can cause a malfunction. 27 Maintenance Inspections Maintenance inspections are necessary for the user to use this equipment safely. It is important to keep monitor functions in good condition at all times through periodical and appropriate maintenance. [. . . ]