User manual PANASONIC BT-M1950Y

[. . . ] Extension cords used with the equipment must have three cores and be correctly wired to provide connection to the ground. Wrongly wired extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power outlet is grounded or that the installation is completely safe. For your safety, if you are in any doubt about the effective grounding of the power outlet, please consult a qualified electrician. CAUTION: Operation at a voltage other than 120 V AC may require the use of a different AC plug. [. . . ] <NORMAL> Normal background <HALF> Background brightness 50% <BLACK> Background brightness 0% (Black) Used to display the center marker. <OFF> Not displayed <ON> Displayed Used to select the marker to be displayed using the GPI terminal "MARKER1 ON/OFF" operation ( page 23). <4:3> <14:9> <VISTA> <93%> <88%> 4:3 marker 14:9 marker VISTA marker 93% Area marker 88% Area marker <13:9> <CNSCO> <95%> <90%> <80%> 13:9 marker CNSCO marker 95% Area marker 90% Area marker 80% Area marker CENTER MARKER*1 GPI PRESET1 GPI PRESET2 Used to select the marker to be displayed using the GPI terminal "MARKER2 ON/OFF" operation ( page 23). <4:3> <14:9> <VISTA> <93%> <88%> 4:3 marker 14:9 marker VISTA marker 93% Area marker 88% Area marker <13:9> <CNSCO> <95%> <90%> <80%> 13:9 marker CNSCO marker 95% Area marker 90% Area marker 80% Area marker *1 When controlling the marker settings using the GPI function ( page 23), these settings become disabled. These are not operated when the 2 screens are displayed. *2 These are only enabled when the HD signal and SD signal aspect ratio settings are 16:9. *3 These are only enabled when the SD signal aspect ratio setting is 4:3. 14 Main Menu (continued) Types of MARKER g 16:9 marker (Displayed when using HD, or when using SD with a 16:9 aspect ratio) The marker is only displayed as a vertical bar. In addition, the section becomes the "MARKER BACK" item. Area marker A dotted line is displayed as the marker. 95% Area marker 93% Area marker 4:3 marker 13:9 marker 90% Area marker 88% Area marker 14:9 marker VISTA marker, CNSCO marker A horizontal dotted line is displayed as the marker. 80% Area marker g 4:3 marker (Displayed when using SD with a 4:3 aspect ratio) A dotted line is displayed as the marker. VISTA marker CNSCO marker When "UNDER" is set in "SCAN" in the "VIDEO CONFIG" menu, a vertical dotted line is also displayed as the marker. 95% Area marker 93% Area marker VISTA marker CNSCO marker 90% Area marker 88% Area marker 80% Area marker g Center marker The marker is displayed in the center of the picture. Center marker 15 Main Menu (continued) VIDEO CONFIG The underlined values are factory preset setting values. Sub menu GAMMA SELECT*2 FILM GAMMA*2 Settings <NORMAL> <FILM>*1 <VARICAM> <OTHER> <USER0­63>*5 <D93> <D65> <D56> <VAR1> <VAR2> <VAR3> Explanation Used to select the gamma curve. When FILM is selected, left of the screen. The underlined values are factory preset setting values. Settings <USER0­63> <D93> <D65> <D56> Explanation Used to select the color temperature that will become the basis for adjustments. <USER0­63> Adjustable settings 0­63 (color temperature around 3000K­9300K) <D93> Color temperature around 9300K <D65> Color temperature around 6500K <D56> Color temperature around 5600K Used to adjust the WB in the HIGH level R component. *1 Used to adjust the WB in the HIGH level G component. *1 Used to adjust the WB in the HIGH level B component. *1 Used to adjust the WB in the LOW level R component. *1 Used to adjust the WB in the LOW level G component. *1 Used to adjust the WB in the LOW level B component. *1 WB-HIGH RED WB-HIGH GREEN WB-HIGH BLUE WB-LOW RED WB-LOW GREEN WB-LOW BLUE RESET <0­60> (Factory preset settings: 30) This returns the "WB-HIGH RED" ­ "WB-LOW BLUE" settings to the factory presets. *1 When adjusting, the item display moves to the lower part of the screen. SYSTEM CONFIG The underlined values are factory preset setting values. Sub menu BACKLIGHT FUNCTION1 Settings < 0­60 > <HV DELAY> <AUTOSETUP> <BLUE ONLY> <GAMMA SELECT> <SD ASPECT> <SCAN> <SUB WINDOW> <UNDEF> <HV DELAY> <AUTOSETUP> <BLUE ONLY> <GAMMA SELECT> <SD ASPECT> <SCAN> <SUB WINDOW> <UNDEF> Explanation Used to adjust the brightness of the liquid crystal backlight. Used to select the functions assigned to [FUNCTION1] and [FUNCTION2] (front buttons). <HV DELAY>*2 Displays the synchronizing signal (horizontal, vertical). The display is switched in the following order. OFF H-Delay V-Delay HV-Delay OFF <AUTOSETUP>*5 Used to automatically adjust the PC display. <BLUE ONLY> Used to cut the red and green signals. You can check the hue (PHASE) and depth of color (CHROMA). [. . . ] If a fan stop error occurs, setting "FAN MOTOR" to "OFF" in the "SYSTEM CONFIG" menu (refer to page 18) allows you to continue using the monitor with reduced screen brightness. Fan stop Error Maintenance · To clean the cabinet or surface of the liquid crystal protection panel, gently wipe with a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth dipped in a weak detergent solution and then wrung-out to clean the surfaces, then use a dry cloth to finish. Water or similar substances getting inside the monitor can cause a malfunction. · Never use thinner or benzene to clean this unit. [. . . ]