User manual PANASONIC BT-LS1400P

[. . . ] For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www. eiae. org. > WARNING: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE AND KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS--USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS, AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT. CAUTION: CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE, USE THE RECOMMENDED ACCESSORIES ONLY. Do not install or place this unit in a bookcase, built-in cabinet or any other confined space in order to maintain adequate ventilation. Ensure that curtains and any other materials do not obstruct the ventilation to prevent risk of electric shock or fire hazard due to overheating. CAUTION: TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, REFER MOUNTING OF THE OPTIONAL UNIT TO AUTHORIZED SERVICE PERSONNEL. indicates safety information. 2 For your safety THIS APPARATUS MUST BE GROUNDED To ensure safe operation the three-pin plug must be inserted only into a standard three-pin power outlet which is effectively grounded through normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to the ground. [. . . ] Overscanning displays are used by consumer products although their scanning ratio differs from product to product. 7 4 BLUE ONLY button The chroma and phase can be adjusted more accurately using SMPTE color bars when this button is pressed. POWER INPUT SCAN BLUE MENU/ EXIT ENTER 5 MENU selector buttons VOLUME MENU 1 24 3 5 6 1 Power switch This is the main power switch. When the power is ON, the LED (green) above the switch lights. 2 INPUT selector button This is used to select the signal input, and each time it is pressed, the input is switched in the following sequence: LINE A > LINE B > CMPNT> SDI > LINE A. <Note> The SDI signal input can be selected only when the BTYA210G, available as an optional accessory, is installed. These are used to display the menus and perform the adjustments and settings. MENU/EXIT: Press this button to exit the menu display and menu. Further, if this button is pressed after the menu item has been selected, the menu will be exited with the item entered. WX: Press these buttons to move the cursor up or down or to select menu items. ENTER: Press this button to select menu items or enter settings. 6 Volume controls The volume level is altered by pressing the up (W) and down (X) buttons. 7 Speaker 8 Tally lamp The lamp (red) lights due to remote control operation. See "REMOTE specifications" (page 10) for details. 5 Parts and their functions (rear panel) = > ? @ LINE A VIDEO S-VIDEO IN AUDIO OUT 9 IN LINE B VIDEO OUT IN S-VIDEO OUT R IN LR AUDIO L OUT : IN CMPNT OUT IN COMPONENT IN OUT R AUDIO IN LR REMOTE L Y P B P R R L ; 9 LINE-A These connectors are for composite signal and S-video signal and audio signal input. Priority is given to the Svideo signal for input. < ?Security lock This can be used to connect a commercially-available theft-prevention cable (manufactured by Kensington). This security lock is compatible with the Microsaver Security System from Kensington. Contact details for this company are given below. KensingtonTechnology Group ACCO Brrands Inc. 2855 Campus Drive San Mateo, CA 94403 USA Tel (650)572-2700 Fax(650)572-9675 http://www. kensington. com/ http://www. gravis. com/ NOTE: information given above may be changed in future. : LINE-B These connectors are for composite signal and S-video signal and audio signal input. Priority is given to the Svideo signal for input. ; CMPNT These connectors are for component signal input and audio signal input. When the option SDI input unit BT-YA210G is installed, these connectors are also used for SDI audio input. <Note> It is recommended to use the Y CMPNT connector for input of monochrome signals. @ Screw hole for cable clamp This screw hole is for attaching the clamp for the power cord. Refer to the following when attaching the clamp. < REMOTE connector This 9-pin, D-sub connector is for remote control purposes. Place the power cord in the accessory clamp. = SD-SDI connectors (optional) These are SD-SDI input connectors (BNC) with active thru output. > AC IN power socket This is the AC power socket. Connect the accessory power cord here. Fix the clamp to the monitor using the screw provided. 6 How to use the on-screen menus Press the MENU/EXIT button to display the main menu on the screen. MENU/EXIT button ª Menus [MAIN MENU] PICTURE VIDEO CONFIG SYSTEM CONFIG MAINTENANCE [INPUT] LINE A The following items appear on the main menu. 1 2 3 4 5 1 PICTURE 4 4 4 4 This menu is used to perform the settings relating to the picture. 2 VIDEO CONFIG This menu is used to perform aspect and component input level settings. 3 SYSTEM CONFIG This menu is used to set the backlight brightness, status displays, input switching skip and REMOTE ON or OFF. 4 MAINTENANCE This menu is used to display the running time of the LCD monitor. 5 [INPUT] The currently selected signal--whether LINE A, LINE B, CMPNT or SDI (optional)--is displayed here. 7 How to use the on-screen menus ¥ PICTURE menu The menu items shown below appear when the PICTURE menu is selected on the main menu. [PICTURE MENU] MODE BROADCAST CONTRAST 60 BRIGHT 30 CHROMA 30 PHASE 30 SHARPNESS 30 AI OFF NR OFF COLOR TEMP D93 3D Y/C OFF [LORD FACTORY] PHASE The phase can be adjusted here. Use the blue-only function to adjust the level while viewing the SMPTE color bars. SHARPNESS The appropriate sharpness in line with the signal characteristics can be set here. AI Dynamic images can be received when this is set to ON. MODE The video mode is selected here. [. . . ] Further, it is recommended to secure the stand using the screw holes when it is to be permanently located. <Note> Take care not to catch your fingers or hands when tilting the stand. Rack mounting The unit can be mounted into a 19-inch standard rack (height: 7U size) if the optional rack-mounting adaptors (BT-MA1400G) are used. Refer to the following when attaching the adaptors. 1 Remove the stand from the main monitor unit. 3 Attach the BT-MA1400G rack mount adapter using the two screws which were removed in step 1 and six screws which were removed in step 2. Screws 2 Remove the six screws from the monitor. Screws <Note> Keep the temperature inside the rack to between +41 oF (5 oC) and +95 oF (35 oC). 11 Maintenance Wipe off any dust or dirt on the monitor and LCD panel with a soft cloth. For stubborn dirt or stains, wipe the monitor and LCD panel with a cloth that has been lightly dampened with well-diluted kitchen detergent and wrung out thoroughly, then finish it off with a dry cloth. The monitor may malfunction if even one drop of water gets into the internals. Do not spray detergent or other cleaners directly on the monitor or LCD panel. The monitor may malfunction if even one drop of water gets into the internals. 12 Specifications [GENERAL] Power supply: AC 100 V to 240 V, 50-60 Hz Power consumption: 0. 98 A to 0. 54 A indicates safety information. [Video signal output] LINE A: Loop-through output, 75 h automatic termination (BNC, S connector) LINE B: Loop-through output, 75 h automatic termination (BNC, S connector) SDI (optional): Buffer output (BNC, 480/59. 94i) aa Dimensions (WaHaD): 14 a 12-1/8 a 2-13/16 inch (main unit only) (356 a 308. 5 a 71. 5 mm) 14 a 13-3/8 a 7-3/8 inch (with monitor stand) (356 a 340 a 187 mm) Weight: 10. 5 lbs (4. 6 kg) (main unit only) 12. 4 lbs (5. 6 kg) (with monitor stand) Ambient operating temperature: 41 °F to 95 °F (5°C to 35°C) Ambient operating humidity: 20% to 80% (no condensation) Ambient temperature for storage: ­4 °F to 140 °F (­20°C to +60°C) Ambient humidity for storage: 10% to 90% (no condensation) [Audio input] LINE A: L/R input (RCA, phono pin), 0. 5 Vrms LINE B: L/R input (RCA, phono pin), 0. 5 Vrms CMPNT: L/R input (RCA, phono pin), 0. 5 Vrms SDI (optional): Audio signals for CMPNT input [Audio output] LINE A: Loop-through output, L/R (RCA, phono pin) LINE B: Loop-through output, L/R (RCA, phono pin) Speakers: Stereo (1 W + 1 W) [Panel] Number of pixels: 921, 600 (640 (H) x 480 (V) , RGB) Angle of view: Top-bottom direction: 160°; left-right direction: 160° a Screen dimensions (WaH): 288 a 217 (mm) (4:3 aspect) [Other] REMOTE: D-sub, 9 pin [Video signal input] LINE A: NTSC composite (BNC) 1. 0 Vp-p S video signals (S connector prioritized) Y: 1. 0 Vp-p C: 0. 268 Vp-p LINE B: NTSC composite (BNC) 1. 0 Vp-p S-video signals (S connector prioritized) Y: 1. 0 Vp-p C: 0. 268 Vp-p CMPNT: Y: 1. 0 Vp-p PbPr: 0. 7 Vp-p (BNC, 480/59. 94i, 480/59. 94P) SDI (optional): Component serial digital (BNC, 480/59. 94i) [Accessories provided with the monitor] Power cable a 1 Operating Instructions a 1 Cable clamp a 1 Screw for cable clamp a 1 13 Memo 14 Memo 15 PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA Executive Office: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000 EASTERN ZONE: One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621 Southeast Region: 1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835 Central Region: 1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200 WESTERN ZONE: 3330 Cahuenga Blvd W. , Los Angeles, CA 90068 (323) 436-3500 Government Marketing Department: 52 West Gude Drive, Rockville, MD 20850 (301) 738-3840 Broadcast PARTS INFORMATION & ORDERING: 9:00 a. m. [. . . ]