User manual PANASONIC BT-S950P

[. . . ] Operating Instructions Model BT-S950P BT- S950 VOLUME PHASE CHROMA BRIGHT CONTRAST UNDER SCAN PULSE CROSS MONO BLUE POWER LINE A EXT LINE B SYNC V. HOLD PAL NTSC NTSC PAL 4:3 16:9 Color Video Monitor Before attempting to connect, operate or adjust this product, please read these instructions completely. Printed in Thailand VQT9992 LCT1182-001A-H 0302-PN-Y-U-JMT P SAFETY PRECAUTIONS WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. FCC INFORMATION (U. S. A. only) CAUTION: Changes or modifications not approved by PANASONIC could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Adjust the CHROMA and PHASE controls until the density and brightness of each blue bar are the same. 13 MONO (color off) switch Selects the screen mode (color or B/W). Useful when you want to check the white balance. (G) : Color screen (g) : B/W screen Adjust the blue bars to the same density and brightness. (continued on the next page = ) 5 CONTROLS AND FEATURES Rear < Rear Panel > 24 25 SERVICE (cont'd) VIDEO A IN OUT 15 VIDEO B IN OUT VIDEO A IN OUT 1 2 B VIDEO B R CUT OFF G IN OUT 16 LINE A IN WARNING THIS APPARATUS MUST BE EARTHED LINE A R IN S-VIDEO OUT OUT S-VIDEO OUT 1 2 DRIVE G EXT SYNC IN EXT SYNC IN OUT AUDIO LINE B 17 AUDIO LINE B IN OUT AC IN IN OUT DC IN 12V + NORMAL 18 19 NORMAL AFC FAST - TALLY/ REMOTE AFC FAST 20 21 22 23 To AC outlet (120 V AC, 50 Hz/60 Hz) TALLY/ REMOTE 15 VIDEO A terminals Video signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected. IN : Video signal input terminal OUT : Bridge-connected video signal output terminal 17 EXT SYNC terminals External sync signal input (IN) and output (OUT) terminals. The output terminal is bridge-connected. IN : Input terminal for the external sync signal OUT : Bridge-connected output terminal Notes: * For corresponding audio signals, use the AUDIO A terminals *. * Also refer to the Basic Connection Example on page 8. Note: * Also refer to the Basic Connection Example on page 8. 18 AUDIO A terminals Input (IN) and output (OUT) terminals for the audio signal corresponding to the VIDEO A terminals %. The output terminal is bridge-connected. IN : Audio input terminal OUT : Bridge-connected output terminal 16 VIDEO B terminals Video signal input (IN) and output (OUT) terminals for both composite and S-VIDEO (Y/C) terminals. Each output terminal is bridge-connected. [BNC terminals] IN : Video signal input terminal OUT : Bridge-connected video signal output terminal [S-VIDEO (mini-DIN 4-pin) terminals] IN : S-VIDEO (Y/C) signal input terminal OUT : Bridge-connected S-VIDEO signal output terminal Note: * For corresponding video signals, use the VIDEO A terminals %. 19 AUDIO B terminals Input (IN) and output (OUT) terminals for the audio signal corresponding to the VIDEO B terminals ^. The output terminal is bridge-connected. IN : Audio input terminal OUT : Bridge-connected output terminal Notes: * For corresponding audio signals, use the AUDIO B terminals (. * Also refer to the Basic Connection Example on page 8. S-VIDEO terminal pin layout 3 1 Note: * For corresponding video signals, use the VIDEO B terminals ^. Pin No. 1 2 3 Signal GND (Y) GND (C) Y C IN 20 AFC switch Selects the AFC (Automatic Frequency Control) time constant for the horizontal sync circuit. Correct the skewed portion of the picture. NORM position : Normal mode FAST position : Fast mode (fast: smaller time constant) S-VIDEO OUT 4 3 2 1 4 2 4 6 < Rear Panel > 24 25 SERVICE IN OUT VIDEO A IN OUT 1 2 B VIDEO B R CUT OFF G IN OUT NORMAL IN WARNING THIS APPARATUS MUST BE EARTHED LINE A R AFC FAST OUT S-VIDEO OUT 1 2 DRIVE G EXT SYNC IN AUDIO LINE B AC IN IN OUT 21 TALLY/ REMOTE DC IN 12V + NORMAL AFC FAST - TALLY/ REMOTE 22 Power input connector Supply power to either the AC IN or DC IN 12 V connector. [AC IN] Connect the provided AC power cord between the AC IN connector and an AC outlet (120 V AC, 50 Hz/60 Hz). [DC IN 12 V] Connect the 12 V DC power plug to the DC IN 12 V connector. 22 23 To AC outlet (120 V AC, 50 Hz/60 Hz) 21 TALLY/REMOTE terminal External control terminal (DIN 8-pin). [. . . ] Is the audio cable disconnected? Shaking picture. No color, wrong color, or dark picture. Is the monitor close to a device generating a strong magnetic field (motor, transformer, etc. )?Is the MONO (color off) switch set properly?Has the picture control setting (CONTRAST, BRIGHT, CHROMA or PHASE) been changed? Unnatural, irregularly colored, or distorted picture. [. . . ]