User manual PANASONIC CF-VDD712

[. . . ] The following are registered trademarks of IBM Corporation:IBM, IBM PC AT, IBM PS/2. The following are registered trademarks of Microsoft Corpora ti on :M S , M S - DO S , Windows 95. PCMCIA is a trademark of the Personal Computer Memory Card International Association. Phoenix and the Phoenix logo are registered trademarks of Phoenix Technologies, Ltd. [. . . ] An RJ-11 jack in the back of your notebook allows you to connect a telephone line to the internal modem. A docking port on the back of your notebook allows the connection of a docking device. s A serial port in the back of your notebook allows you to connect serial devices, such as RS-232C serial printers or scanners. A parallel port in the back of your notebook allows you to connect a parallel printer, photo or text scanner, etc. An external monitor port in the back of your notebook allows you to connect an external monitor. s s PC Card slots in the left side panel of your notebook allow you to install PC Cards, IC memory cards (SRAM card) or Zoomed Video cards (Slot 0 only). The dual Multi-function bays in the front of your notebook allow you to install the CD-ROM drive, the floppy disk drive, an optional second hard drive, or an optional second Lithium ion battery. A compartment on the bottom of your notebook allows you to install a memory upgrade module. A microphone jack on the right side of your notebook allows you to connect a mono microphone. A stereo line in jack on the right side of your notebook allows you to connect a sound source such as a cassette recorder. s s s This section describes how to install and remove equipment for each of the expansion features. s s s s s s 96 LifeBook 7 00 Series fr om Fujitsu User Installable Features Floppy Disk Drive Bay 1 Modules Bay 2 Modules CAUTION All Multi-function bay devices except the Lithium ion battery must be installed and removed with the power switch in the Off position. The Lithium ion battery may be warm swapped (power on but unit in Suspend mode). (See Power Off on pages 24-25 and Bridge Battery on page 27. ) The Multi-function bays support a variety of configurations. Multi-function Bay 1 supports: s Second Hard Drive CD-ROM Drive Floppy Disk Drive Device Adapter for Bay 2 Lithiun ion Battery Device Adapter for Bay 2 Lithium ion Battery Figure 4-1 Multi-function Bay Modules 3. 5" floppy disk drive (included with your notebook. ) Lithium ion battery (included with your notebook. ) MULTI-FUNCTION BAY DEVICES The bays in the front panel of your notebook accommodate the CD-ROM drive, the floppy disk drive, the Lithium ion batteries (a second battery is optional) or the optional second hard drive. CAUTION Do not use your notebook with either of the Multi-function bays empty. To Install a Device in Multi-function Bay 2 Figure 4-3 Removing and Installing a Device in Multi-function Bay 2 To Install or Remove a Device in Multifunction Bay 2. Close all files and exit all applications. Turn off power to your notebook, close the display and remove the AC adapter. (See pages 24-25 for more information. ) 3. Turn your notebook upside down with the bay openings toward you. 4. Orient the item to be installed with the finger ridge away from the body of your notebook and the connector toward the body of your notebook. With the module connector toward the back of your notebook align the grooves on the side of the device with the tracks in the side of the bay. Slide the module toward the back of your notebook until it clicks into place. Figure 4-4 Installing a Module in the Device Adapter for Multi-function Bay 2 To Install a Module in the Device Adapter for Multi-function Bay 2. Align the device adapter for Multi-function Bay 2 with the solid side up and the rounded edges toward you. Align your Multi-function Bay 1 device with the finger ridge up and the connector away from you. 99 Section Four 3. Set the device adapter for Multi-function Bay 2 on top of the Multi-function Bay 1 device and adjust until the finger ridge shows through the hole in the device adapter for Multi-function Bay 2, and the alignment pins on the Multi-function Bay 1 device fit in the small round holes of the device adapter for Multi-function Bay 2. Hold the two parts together while installing in Multi-function Bay 2 according to the preceding directions. [. . . ] 8, 30, 72, 96, 106, 113, 115, 124, 149 150, 152, 153, 155, 156, 158, 163, 165 Quiet boot . 3, 103, 110, 138, 140, 148, 151, 154-155, 159-160, 164 Real time clock . 22, 25, 34, 43, 45-46, 52, 54, 78 93-94, 113, 115, 123-126, 129, 138, 164 Resume, . 5-6, 19, 21, 25, 29, 39-40 42-46, 78, 80, 84-85, 87, 112, 114, 123 129-130, 132, 135-136, 139, 164, Resume On Time, . [. . . ]