User manual PANASONIC CF-07LZ5ZYDM

[. . . ] 17 Touch Pad (Basic Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Digitizer (Basic Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Operating in Tablet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not apply "Driver Updates" even if a message to update a driver appears. If a driver page 46) update is required, contact Panasonic Technical Support. ( [start] - [All programs] - [Windows Update] Saving Data on the Hard Disk Do not expose your computer to shock. Use care when handling your computer, shock may damage your hard disk or make your software applications and data unusable. Do not power down your computer while software applications are running or hard disk drive indicator is on. Properly shut Windows down to avoid problems. Backing up data to disks will limit damage should trouble occur to your computer or should you inadvertently change or erase data. Use the security function for all important data. ( "Security Measures" and "SD Memory Card Security Function") Hard Disk Lock When the Hard Disk Lock is set to [Enable], it is impossible to read/write data from/to the hard disk when the hard disk is installed in a different computer. When the hard disk is returned to the original computer, you can read/write data as before. In this case, however, make the settings in the Setup Utility exactly the same as they were before the hard disk was removed. Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed. The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from. If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and use another bootable disk if not. If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility. · If the hard disk is recognized, perform the reinstallation procedure. · If not, contact Panasonic Technical Support. If a device is connected to the USB port, disconnect the device, or run the Setup Utility and set [Legacy USB Support] in [Advanced] menu to [Disable]. If the extended RAM module has not been inserted properly, or if an extended RAM module other than one matching the specifications has been inserted, a beep will sound and the message "Extended RAM Module Failed" will be displayed when turning the power on. In this case, turn the power off, confirm that the extended RAM module meets the specifications, and reinsert it. 0271: Check date and time settings 0280: Previous boot incomplete - Default configuration used Press <F2> to Setup Operating System not found Extended RAM Module Failed 29 Troubleshooting To run the Setup Utility 1 Restart the computer. 2 Press F2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. Dealing with Problems (Summary) When a problem occurs, refer to this page. [. . . ] and Alaska. DIAL TOLL FREE: 1-800-LAPTOP5 Correspondence requesting product information should be sent to: Panasonic Computer Solutions Company 50 Meadowlands Parkway, Panazip 2F-5, Secaucus, NJ 07094 46 For Canada PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY Coverage ­ Panasonic Canada Inc. ("PCI") warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified. Scope of Coverage Whole Product (except Batteries), AC adaptor and CD-ROM (if factory installed) Batteries, CD-ROM (unless factory installed), Port Replicator, Extra Memory Modules and all other Peripherals, Options and Accessories Period of Coverage Three (3) Years from Date of Original End User Customer Purchase One (1) Year from Date of Original End User Customer Purchase Type of Failure Coverage Defective Materials or Workmanship Defective Materials or Workmanship Remedy ­ In the event of a warranty claim, contact PCI's representatives within the applicable warranty period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A. M. (excluding holidays) for instructions on how to obtain service. [. . . ]