User manual PANASONIC CF-07LZXXXXX

[. . . ] ® Personal Computer Reference Manual Model No. CF-07 Series Contents 98 2000 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Standby/Hibernation Functions . . . . . . . . . . . . . . . . . . . . . . . 3 Security Measures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Once the driver of the card is installed, you can insert the card anytime. (To next page) PC Cards Removing a PC Card CAUTION Do not remove a PC Card while your computer is in the standby or hibernation mode. Double-click ( Windows 2000 ) on the taskbar, select the PC Card slot, then select [Stop]. (When removing a PC Card after turning off the computer, this step is not necessary. ) Button 22 CAUTION After selecting ( Windows 2000 ) , do not press [Stop] for [PRISM2 IEEE 802. 11 PC CARD Adaptor-Socket2]. Open the cover, then press the button out, then press the button again. Close the cover. Port Replicator A port replicator is available as an option (CF-VEB071). This device allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector on the bottom of your computer. For more detailed information, refer to the operation manual of the port replicator. 23 Expansion Bus Connector NOTE When connecting the external display to the display port on the port replicator, the characters on the external display may be blurred if 1280 x 1024 (or a higher resolution) is set. In this case, select a resolution that is lower than 1280 x 1024. Printer <Only when the port replicator is connected> 1 Power off your computer ( ( Port Replicator "Starting Up/Shutting Down") Do not shut down using the standby or hibernation mode. 24 2 Connect your computer to the optional port replicator Operating Instructions of the port replicator, page 23) 3 Connect the printer to the port replicator NOTE For more detailed information, refer to the operation manual of the printer. Parallel Port 4 Turn on the printer, then turn on your computer 5 Setting your printer Go to [Start] - [Settings] - [Printers]. Find your printer's icon, click on it, then select [File] - [Set as Default]*. If no icon is available, select [Add Printer] and follow the on-screen instructions. * Windows 2000 : [Set as Default Printer] NOTE For more detailed information, refer to the operation manual of the external display. Confirm whether or not the setting for the [Parallel Port] in the Setup Utility is optimal( page 31) External Display <Only when the port replicator is connected> 25 1 Power off your computer ( Port Replicator ( "Starting Up/Shutting Down") Do not shut down using the standby or hibernation mode. 2 Connect your computer to the optional port replicator Operating Instructions of the port replicator, page 23) 3 Connect the external display to the port replicator NOTE For more detailed information, refer to the operation manual of the external display. External Display Port 4 Turn on the external display, then turn on your computer 5 Select your external display Set your external display for [Monitor] in [Start] - [Settings] - [Control Panel] - [Display] - [Settings] - [Advanced]. When a monitor that does not conform to the Plug & Play standards is connected, select [Change]* and make the monitor settings. * Windows 2000 : [Monitor] - [Properties] - [Driver] - [Update Driver]. NOTE For more detailed information, refer to the operation manual of the external display. The external display will show the same screen size as the wireless display when the latter is connected. Both displays will therefore appear identical. USB Devices Installing a USB device Mini USB Port 26 1 Open the cover, then connect the included USB cable to the mini USB port 2 Connect the USB device to the cable CAUTION Turn the screw in the clockwise direction to fasten it. Screw When inserting a USB device for the first time, the device will only work after being recognized by the computer. Insert the device powering off the computer and wireless display, and then connecting the port replicator, optional USB floppy disk drive, external keyboard and external display. Once the driver of the device is installed, you can insert the device anytime. <When using the port replicator> 1 Power off your computer ( Port Replicator USB Port ( 2 Connect your computer to the optional port replicator Operating Instructions of the port replicator, page 23) "Starting Up/Shutting Down") Do not shut down using the standby or hibernation mode. 3 Connect the USB device to the port replicator NOTE For more detailed information, refer to the operation manual of the USB device. You may need to install drivers compatible with the OS you are using for your USB devices. Follow the on-screen instructions and refer to the operation manual for USB devices on how to install the driver. When a USB device is connected, there are cases the standby or hibernation function will not operate in a normal manner due to the USB device. In addition, a USB device may have to be removed temporarily and the computer restarted in cases where the computer is unable to start up properly. Removing a USB device CAUTION Do not remove a USB device while your computer is in the standby or hibernation mode. 1 Windows 2000 Double-click on the taskbar and select the USB device, then select [Stop] Follow the on-screen instructions. [. . . ] If it is full, delete unnecessary files. Your hard disk content may be corrupted. Is the disc loaded on the tray correctly?To remove a disc when the computer is powered off, insert a sharp object such as the bent-out tip of a paper clip into the emergency hole. [. . . ]