User manual PANASONIC CF-18DHAZXKM

[. . . ] Personal Computer OPERATING INSTRUCTIONS Model No. CF-18 Series Getting Started Appendix Troubleshooting Operation Contents Getting Started Read Me First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Names and Functions of Parts . . . . . . . . . . . . . . . . . . . . . . . . 8 First-time Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 XP Reference Manual · Read Me First · Key Combinations · LED Indicators Operation Starting Up/Shutting Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you do this, the backup region cannot be created. Divide into the partition when the backup region is created. When Disposing of or Transferring Ownership of This Device When disposing of or transferring ownership of this device, erase all data on the hard disk in order to prevent the theft of hard disk data. Even if you delete data or initialize the hard disk through normal Windows commands, data can still be read using special software. In order to erase all data, either have the data erased by a specialist (at a charge) or use the hard disk data erase utility (included) ( page 42). (Note that this hard disk data erase utility does not guarantee that data will be completely erased. ) Also, note that if you transfer ownership of this device without deleting commercial software that you have installed to the hard disk, you may be in violation of the licensing agreement for that software. 27 Operation List of Error Codes When turning on the computer, if one of the following error codes or messages is displayed, follow the instructions shown below. If the problem persists, or if the error code or message displayed is not shown here, contact Panasonic Technical Support. Action If an external keyboard or mouse is connected, disconnect these devices. An error has occurred in the memory that stores the Setup Utility settings. This error occurs when the memory content is changed through some inadvertent operation by a program or other function. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. If the problem persists, the internal clock battery may need to be replaced. 0271: Check date and time set- The data and time setting are incorrect. tings Run the Setup Utility and set the date and time correctly. If the problem persists, the internal clock battery may need to be replaced. 0280: Previous boot incomplete Startup has failed repeatedly, so the Setup Utility settings have been returned to their default - Default configuration used values, and the computer has been restarted. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. 1 0613: Serial Port* configura- I/O address and IRQ settings are in conflict. tion changed Run the Setup Utility and change the settings in [Advanced] menu so there is no port 0614: Serial Port*1 config. - device disabled *1 The port name, such as A or B, is displayed, indicating the conflicting ports. Error Code/Message 0211: Keyboard error 0251: System CMOS checksum bad - Default configuration used Press <F1> to resume, <F2> to Setup Operating System not found Troublesahooting Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed. The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from. If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and change it to another if not. [. . . ] A purchase receipt or other proof of date of original purchase is required before warranty service is performed. Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the balance of the original period of warranty coverage. No Coverage ­ This Limited Warranty does not cover products purchased outside Canada. [. . . ]