User manual PANASONIC CF-18KHHZBBM

[. . . ] OPERATING INSTRUCTIONS Personal Computer Model No. CF-18 Series Getting Started Appendix Troubleshooting Operation Contents Getting Started Read Me First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Names and Functions of Parts . . . . . . . . . . . . . . . . . . . . . . . . 9 First-time Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 XP Reference Manual · Read Me First · Key Combinations · LED Indicators Operation Starting Up/Shutting Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Connect the devices properly, paying close attention to the condition and position of the connectors. If a connection cannot be made easily, do not apply undue force; check once more to confirm the condition and position of the connector (alignment of pins, etc. ). If the connector has holding screws, fasten the screws firmly. Do not carry the computer with cables attached, and do not pull on the cables forcefully. When Changing Hard Disk Partitions When using the hard disk backup function, divide the hard disk into partitions when a backup area is created ( page 39). If you divide the hard disk into partitions before creating the backup area, the backup area cannot be created. When Disposing of or Transferring Ownership of This Device When disposing of or transferring ownership of this device, erase all data on the hard disk in order to prevent the theft of hard disk data. Even if you delete data or initialize the hard disk through normal Windows commands, data can still be read using special software. In order to erase all data, either have the data erased by a specialist (at a charge) or use the hard disk data erase utility page 43). (Note that this hard disk data erase utility does not guarantee that data (included) ( will be completely erased. ) Also, note that if you transfer ownership of this device without deleting commercial software that you have installed to the hard disk, you may be in violation of the licensing agreement for that software. Operation Wireless LAN (only for models with wireless LAN) To prevent theft of data or unauthorized access to the hard disk via a wireless LAN If you plan to use wireless LAN functions, we recommend that you do so only after making the appropriate security settings, such as for data encryption. 28 List of Error Codes When turning on the computer, if one of the following error codes or messages is displayed, follow the instructions shown below. If the problem persists, or if the error code or message displayed is not shown here, contact Panasonic Technical Support ( Error Code/Message 0211: Keyboard error 0251: System CMOS checksum bad - Default configuration used Action If an external keyboard or mouse is connected, disconnect these devices. An error has occurred in the memory that stores the Setup Utility settings. This error occurs when the memory content is changed through some inadvertent operation by a program or other function. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. If the problem persists, the internal clock battery may need to be replaced. The date and time setting are incorrect. Run the Setup Utility and set the date and time correctly. If the problem persists, the internal clock battery may need to be replaced. Startup has failed repeatedly, so the Setup Utility settings have been returned to their default values, and the computer has been booted. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. I/O address and IRQ settings are in conflict. Run the Setup Utility and change the settings in [Advanced] menu so there is no port conflicts. 0271: Check date and time settings 0280: Previous boot incomplete - Default configuration used 0613: Serial Port*1 configuration changed 0614: Serial Port*1 config. error - device disabled *1 The port name, such as A or B, is displayed, indicating the conflicting ports. Press <F2> to Setup Operating System not found Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed. [. . . ] (excluding holidays) for instructions on how to obtain service. A purchase receipt or other proof of date of original purchase is required before warranty service is performed. Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the balance of the original period of warranty coverage. [. . . ]