User manual PANASONIC CF-27EXXXXXX

[. . . ] ® Personal Computer Reference Manual CF-27 Series Contents 95 Key Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Panasonic Hand Writing (Touch Pad) . . . . . . . . . . . . . . . . . . . . . 4 Suspend/Hibernation Functions . . . . . . . . . . . . . . . . . . . . . . [. . . ] below <Uninstalling the touchscreen driver> When you want to uninstall the touchscreen driver, follow the steps below. 1 Select [Start] - [Programs] - [Touchscreen] - [Uninstall]. 2 Simply follow the on-screen instructions. <When you use the touchscreen function again> 1 In [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [Mouse] - [AHL/AR5000 and Digitouch Controllers], delete the check mark for [Disable in this hardware profile] in [Device Usage], press [OK], then press [Close]. If uninstalling the touchscreen driver, reinstall the driver following the steps below. 1 In [Start] - [Run], input [c:\util\drivers\tscreen\t5setup. exe], then press [OK]. Simply follow the on-screen instructions. (Select the default value. ) If the computer asks you to reboot the computer, press [Yes]. 2 When the Calibration screen is displayed*, point the cursor. *It is displayed first time only after the computer was rebooted. 3 When the message [Press <F2> to enter SETUP] is displayed, press F2 and then run the Setup Utility. 4 Select [Advanced] menu and set [Serial Port B] to [Enable] and [Device] to [Touchscreen]. At the confirmation message, select [Yes] and press Enter . The computer will reboot. Using a Printer 1 2 Power off your computer ( "Starting Up/Shutting Down") Do not shut down using the suspend or hibernation mode. 27 Connect the printer to your computer 3 Parallel Port Turn on the printer, then turn on your computer with the LCD panel opened 4 Setting your printer Go to [My Computer] - [Printers]. Find your printer's icon, double-click on it, and click [File] - [Set As Default]. If no icon is available, select [Add Printer] and then follow the on-screen instructions. NOTE You may need to install a driver for your printer. Simply follow the onscreen instructions and refer to the operation manual of the printer on how to install the driver. Using an External Display 1 Power off your computer ( "Starting Up/Shutting Down") Do not shut down using the suspend or hibernation mode. 28 2 Connect the external display to your computer NOTE For more detailed information, please refer to the operation manual of the external display. 3 Turn on the external display, then turn on your computer with the display opened You can select either an external display, LCD or simultaneous with Fn + F3 . In addition, you can set the display to use during start-up with the following procedure. External Display Port 1 2 3 Run the Setup Utility ( Using Using and and page 34) , select [Main] , select [Display] and press Enter , select the display to use and 4 Using 5 Press and press Enter F10 , then select [Yes] 6 Select your external display Set your external display for [Monitor] in [Start] - [Settings] - [Control Panel] - [Display] - [Settings] - [Advanced Properties]. When a monitor that does not conform to the Plug & Play standards is connected, select [Change] and make the monitor settings. Using USB Devices Installing USB Devices 29 1 Run the Setup Utility ( page 34) 2 Using and , select [Power] 3 Using and , select [Power Management Mode] and press Enter USB Port 4 Using and , select [Off] and press Enter 5 Using and , select [Power Switch] and press Enter 6 Using and , select [Off] and press Enter 7 Using and , select [Fn+F7/Fn+F10] and press Enter 8 Using and , select [Disable] and press Enter 9 Press F10 , then select [Yes] 10 Install the Windows 95 USB device drivers 1 In [Start] - [Run], input [c:\util\msupdate\usb\usbsupp. exe], then press [OK]. At the confirmation message, press [Yes]. 2 Read the [END-USER LICENSING AGREEMENT] and press [Yes] or [No]. · Installation will start if [Yes] is pressed. · Installation will be aborted if [No] is pressed. 3 At the display indicating the completion of installation, press [OK]. The computer will automatically restart. 4 In [Start] - [Run], input [c:\util\msupdate\usb\usbcopy. bat], then press [OK]. [. . . ] If a switch is made to the Hand Written mode in Panasonic Hand Writing, any external mouse or trackball connecting to the external keyboard/mouse port will not operate. Reconnect the device after quitting the Hand Written mode. If the device still does not work, try restarting the computer. Make sure the card is properly inserted. [. . . ]