User manual PANASONIC CF-27FCCXXXX

[. . . ] ® Personal Computer Reference Manual CF-27 Series Contents 95 NT Key Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Touch Pad (Advanced) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If an attempt is made, an error message may be displayed or a message prompting you to format the disk may appear. When this message appears, press the [Cancel] or [No] to close the display. The above contents will no longer be displayed when the drive is re-connected or when the computer is restarted. When the Superdisk drive pack is installed in the multimedia pocket, the floppy disk drive cannot be used as an external floppy disk drive. The CD-ROM pack, DVD-ROM drive pack and Superdisk drive pack cannot be used as an external device. Superdisk Drive Pack Windows NT A floppy disk can not be formatted with a Superdisk Drive Pack. Power off, replace a Superdisk Drive Pack with a floppy disk drive, then power on. Format a floppy disk with a floppy disk drive. Using PC Cards PC Card Your computer has two PC Card slots. These slots conform to the PC Card Standard; therefore, communications and SCSI devices may be utilized. The slots allow you to use two Type I or Type II cards (or one Type I and one Type II), or one Type III card. 32 Type I or II Two cards can be used simultaneously. Slot (Socket) 2 Type III One card can be used only in the slot 1. Slot (Socket) 1 CAUTION Please check the PC Cards' specifications. Be sure the total operating current does not exceed the specified limit. Allowable Current (total for two slots) : 3. 3 V: 400 mA, 5 V: 400 mA There are times when both a Type I card and a Type II card will not work at the same time. SRAM and FLASH ROM (except for an ATA interface) cards are not supported. Windows 95 For the following cases, be sure the power has been turned off before proceeding. · When removing a network card · When replacing a CardBus type card with another card (including another CardBus type card) · When inserting one more CardBus type card with one already inserted Do not use a CardBus type card and a non-CardBus type card at the same time. Windows NT ZV and CardBUS cards are not supported. Installing/Removing the PC Card Installing a PC Card Cover Latch Open the cover by sliding the latch. Simply slide the PC Card in until it snaps into place. Please refer to the manual for each card on how to install the card (insertion is typically label-side up). CAUTION When inserting a card, do not force the card in if difficulty is encountered. You may damage the slot, making it impossible to remove the card. Button Label-side up Removing a PC Card CAUTION Do not remove a PC Card while your computer is in the suspend or hibernation mode. Windows 95 Go to [Socket Status] (in [Start] - [Settings] - [Control Panel] - [PC Card (PCMCIA)]), select the PC Card slot and press [Stop]. (When removing a PC Card after turning off the computer, this step is not need. ) Press the button. (To next page) Using PC Cards PC Card Utility Program Windows NT 33 About Phoenix Card ExecutiveTM 2. 0 for Windows NT® When using a Windows NT® model, confirm that Phoenix Card ExecutiveTM 2. 0 for Windows NT® is installed. [. . . ] Check that the proper port settings have been made. Or, you may need to call the manufacturer of the PC Card. Try removing/reinserting the PC Card by following the proper procedure. ( page 32) Windows NT When [Card Executive 2. 0 for NT] is not displayed in [Control Panel], install Phoenix Card ExecutiveTM 2. 0 for Windows NT®. [. . . ]