User manual PANASONIC CF-28MCXXXXX

[. . . ] ® Personal Computer Reference Manual CF-27 Series Contents 98 Key Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Touch Pad (Advanced) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When the SuperDisk drive pack is installed in the multimedia pocket, the floppy disk drive cannot be used as an external floppy disk drive. The CD-ROM pack, DVD-ROM drive pack and SuperDisk drive pack cannot be used as an external device. * With Windows 98, the "Suspend" is called "Standby". Using PC Cards PC Card Your computer has two PC Card slots. These slots conform to the PC Card Standard; Two cards can be used therefore, communications or SCSI devices, etc. , may be utilized. The slots allow you to use two Type I or Type II cards (or one Type I and one Type II), or one Type III card. simultaneously. 29 Type I or II Slot (Socket) 2 CAUTION Check the PC Cards' specifications. Be sure the total operating current does not exceed the specified limit. Allowable Current (total for two slots) : 3. 3 V: 400 mA, 5 V: 400 mA There are times when both a Type I card and a Type II card will not work at the same time. SRAM and FLASH ROM (except for an ATA interface) cards are not supported. For the following cases, be sure the power has been turned off before proceeding. · When removing a network card · When replacing a CardBus type card with another card (including another CardBus type card) · When inserting one more CardBus type card with one already inserted Do not use a CardBus type card and a non-CardBus type card at the same time. Slot (Socket) 1 Type III One card can be used only in the slot 1. Installing/Removing the PC Card Installing a PC Card Open the cover by sliding the latch. Cover Latch Simply slide the PC Card in until it snaps into place. Refer to the manual for each card on how to install the card (insertion is typically label-side up). CAUTION When inserting a card, do not force the card in if difficulty is encountered. You may damage the slot, making it impossible to remove the card. Removing a PC Card Button Label-side up CAUTION Do not remove a PC Card while your computer is in the suspend* or hibernation mode. * With Windows 98, the "Suspend" is called "Standby". Go to [Socket Status] (in [Start] - [Settings] - [Control Panel] - [PC Card (PCMCIA)]), select the PC Card slot and press [Stop]. (When removing a PC Card after turning off the computer, this step is not need. ) Press the button. Slide the PC Card out. NOTE <When using the ZV card> It is necessary to install the SMI VPM driver as followings. 1 In [Start] - [Run], input [c:\util\drivers\video\vpm\setup. exe], then press [OK]. 2 At the [Setup Type], select [Install VPM Drivers only]. The volume setting for the ZV card can be made in the [IIS] part of the [Volume Control] window. Adding Memory RAM Module CAUTION Use a RAM module meeting the RAM module specifications below. If a module is used that does not meet the specifications, there are cases in which data may become unusable or the computer may not operate properly. RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. In addition, it is easy to damage the RAM modules or internal components of the computer. [. . . ] Note that after a driver is installed, the computer must be rebooted. Check that the proper port settings have been made. Or, you may need to call the manufacturer of the PC Card. Try removing/reinserting the PC Card by following the proper procedure. [. . . ]