User manual PANASONIC CF-28PCJAZQM

[. . . ] 16 Touch Pad (Basic Operation) . . . . . . . . . . . . . . . . . . . . . . . . 19 Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Reference Manual · Touch Pad · Touchscreen*1 · Panasonic Hand Writing · Standby/Hibernation Functions · Security Measures · Computing on the Road · Battery Power · Multimedia Pocket · PC Cards · RAM Module · Port Replicator · External Display · Printer · USB Devices · Modem · LAN · Wireless LAN*2 · Hard Disk Drive · Setup Utility · Icon Enlarger · Loupe Utility *1 Only for models with touchscreen *2 Only for models with wireless LAN Troubleshooting List of Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and change it to another if not. If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility. · If the hard disk is recognized, perform the reinstallation procedure. · If not, contact Panasonic Technical Support. If a device is connected to the USB port, disconnect the device, or run the Setup Utility and set [Legacy USB Support] in [Advanced] menu to [Disable]. If the extended RAM module has not been inserted properly, or if an extended RAM module other than one matching the specifications has been inserted, a beep will sound and the message "Extended RAM Module Failed" will be displayed when turning the power on. In this case, turn the power off, confirm that the extended RAM module meets the specifications, and reinsert it. Extended RAM Module Failed To run the Setup Utility 1 Restart the computer. 2 Press F2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. 25 Troubleshooting Dealing with Problems (Summary) When a problem occurs, refer to this page. The "Reference Manual" also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. This message may appear when certain USB devices are connected. Remove the USB device, or set [Legacy USB Support] in [Advanced] menu of the Setup Utility to [Disable]. If the message still appears even after trying the above two measures, this may be an indication that some type of hard disk failure has occurred. This screen appears because the Battery Recalibration was canceled before Windows was shut down last. To start up Windows, turn off the computer by sliding the power switch, and then turn it back on again. The date and time are incorrect When resuming from the standby or hibernation mode, [Enter Password] does not appear even if a password has been set in the Setup Utility Troubleshooting When the administrator password is forgotten When "Remove disks or other media. Press any key to restart" (or a similar message) is displayed [Executing Battery Recalibration] screen is displayed 26 Starting Up (continued) When the previous item is not the cause Press F9 in the Setup Utility ( "Setup Utility"). This will restore the Setup Utility's settings to their default values (except the password settings). Check a disk error using the following procedure. 1 Select [Local Disk(C:)] with the right button in [start] - [My Computer], and select [Properties]. 3 Select [Start] after selecting required items in [Check disk options]. At startup, hold down F8 when [Panasonic] boot screen disappears*1, and release your finger when the Windows Advanced Options Menu is displayed. [. . . ] Scope of Coverage Whole Product (except Batteries), AC adaptor and CD-ROM (if factory installed) Batteries, CD-ROM (unless factory installed), Port Replicator, Extra Memory Modules and all other Peripherals, Options and Accessories Period of Coverage Three (3) Years from Date of Original End User Customer Purchase One (1) Year from Date of Original End User Customer Purchase Type of Failure Coverage Defective Materials or Workmanship Defective Materials or Workmanship Remedy ­ In the event of a warranty claim, contact PCI's representatives within the applicable warranty period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A. M. (excluding holidays) for instructions on how to obtain service. A purchase receipt or other proof of date of original purchase is required before warranty service is performed. Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on an exchange basis. [. . . ]