User manual PANASONIC CF-41MK3

[. . . ] 7 Computing On the Road . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Using PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Adding Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 2 Press [Next] at the display for the [Display Driver Wizard for PC Cards (PCMCIA)], press [Next] again and then press [Finish]. When the message appears asking whether to reboot the computer, select [Yes]. Adding Memory RAM Module CAUTION 17 RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. In addition, it is easy to damage the RAM modules or internal components of the computer. Therefore, when installing or removing a RAM module, handle the module with extreme care. Installing/Removing the RAM Module 1 Power off your computer ( CAUTION Lever ) Do not shut down using the suspend or hibernation mode. Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. Remove the 2 Turn the computercover the lever and then slide the cover off. over, unlock CAUTION Cover Do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter. Doing so has been known to cause damage, fire or electric shock. Hard Disk Drive Flip 3 Do notover the hard disk from the connector, and let it remain on the frame. disconnect the hard disk (Support the hard disk by hand. ) CAUTION Be careful when handling the hard disk. The hard disk is extremely sensitive to shock. Finger location RAM Module Slot 4 Installing the RAM module Slide in the module at an angle and snap the module into place by pushing down on it. RAM module specifications 144 pins, 60/70 ns, 3. 3 V SO-DIMM, EDO RAM Module Take care not to remove the connector Hook Removing the RAM module 1 2 Open the left and right hooks. Gently remove the RAM module from the slot. 5 Gently return the hard disk into the slot, and then slide the cover back on Be sure to lock the lever. Direct sunlight or white glowing light, such as fluorescent lighting; can cause interference with communications between the ports. When moving your computer while it is transmitting/receiving data. Setting for Infrared Data Communications 1 Run the Setup Utility ( page 24) 2 Using and , select [Supervisor Setup], then press Enter 3 Using and , select [IrDA], set [2F8] with , then press Esc 4 Close the Setup Utility ( Data Communications page 24) 1 Select [Start] - [Programs] - [Accessories] - [Direct Cable Connection] 2 Select [Host] or [Guest], then press [Next] 3 Select [Serial cable on COM4], then press [Next] If [Serial cable on COM4] is not displayed, select [Install New Ports]. Press [Finish] 4 Infrared data communications will begin. NOTE To process at a transfer speed of 4 Mbps, separate application software is necessary. When you select [Start] - [Settings] - [Control Panel], and then select [Infrared], this will give you the conditions for infrared data communications. Online help is available on how to use Direct Cable Connection. Hard Disk Drive To change your hard disk, contact Panasonic Technical Support For information on FAT32, refer to "Technical Information" ( page 30). 23 CAUTION To customers: To change your hard disk, consult your nearest Panasonic Technical Support. Be sure to back up all important data before the change. To technicians (at Panasonic Technical Support): Be careful when replacing the hard disk. The hard disk is extremely sensitive to shock. In addition, static electricity could later affect some internal components. Installing/Removing the hard disk (For technicians at Panasonic Technical Support) Power off your computer 1 Do not shut down using the suspend (or hibernation) mode. CAUTION Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. Lever off the cover 2 Takeyour computer over. Turn Cover Connector 3 Removing/Installing the hard disk To dislodge the hard disk, after flipping it over, pull on the tape . When installing a hard disk, be sure to hold the connector part. Tape 4 Return the hard disk to the slot very gently 5 Put the cover back into place Be sure to lock the lever. Setup Utility Running the Setup Utility To run the Setup Utility, you need to restart your computer. [. . . ] Try setting [Trackball] to disable in the Setup Utility. In some circumstances, if a PS/2 external mouse with a serial interface conversion function is connected to the port, it may not operate normally. Make sure the card is properly inserted. Confirm that the card conforms to the PC Card Standard. [. . . ]