User manual PANASONIC CF-48N4FJUEM

[. . . ] 18 Touch Pad (Basic Operation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Touchscreen (Basic Operation). . . . . . . . . . . . . . . . . . . . . . . . . . 22 Operating in Tablet Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 0280: Previous boot incomplete Startup has failed repeatedly, so the Setup Utility settings have been returned to their default - Default configuration used values, and the computer has been restarted. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. 1 0613: Serial Port* configura- I/O address and IRQ settings are in conflict. tion changed Run the Setup Utility and change the settings in [Advanced] menu so there is no port 0614: Serial Port*1 config. - device disabled *1 The port name, such as A or B, is displayed, indicating the conflicting ports. Error Code/Message 0211: Keyboard error 0251: System CMOS checksum bad - Default configuration used Press <F2> to Setup Operating System not found Troubleshooting Extended RAM Module Failed Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed. The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from. If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and change it to another if not. If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility. · If the hard disk is recognized, perform the reinstallation procedure. · If not, contact Panasonic Technical Support. This computer will not correctly recognize the date and time starting from the year 2100 A. D. Even when a password has been set in the Setup Utility, [Enter Password] does not appear when the computer resumes from the standby or hibernation mode. If you want to use the security function when using the standby or hibernation mode, use the Windows password as follows: 1 Select the account to change in [start] - [Control Panel] - [User Accounts] and set the password. 2 Add the check mark for [Prompt for password when computer resumes from standby] in [Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced]. If you have created a password reset disk ( page 17), a message is displayed when you fail to correctly enter the password. Follow the message's instructions and set the password again by using the password reset disk. If you have not created a password reset disk, after reinstalling, setup Windows and then set the password again. This means a floppy disk that does not contain system startup information has been left in the floppy disk drive. Remove the floppy disk, and press any key. This message may appear when certain USB devices are connected. Remove the USB device, or set [Legacy USB Support] in [Advanced] menu of the Setup Utility to [Disable]. [. . . ] ("PCI") warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified. Scope of Coverage Whole Product (except Batteries), AC adaptor and CD-ROM (if factory installed) Batteries, CD-ROM (unless factory installed), Port Replicator, Extra Memory Modules and all other Peripherals, Options and Accessories Period of Coverage Three (3) Years from Date of Original End User Customer Purchase One (1) Year from Date of Original End User Customer Purchase Type of Failure Coverage Defective Materials or Workmanship Defective Materials or Workmanship Remedy ­ In the event of a warranty claim, contact PCI's representatives within the applicable warranty period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A. M. (excluding holidays) for instructions on how to obtain service. A purchase receipt or other proof of date of original purchase is required before warranty service is performed. [. . . ]