User manual PANASONIC CF-48N4FKUEM

[. . . ] 16 Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 RAM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Error Code/Message 0211: Keyboard error 0251: System CMOS checksum bad - Default configuration used Action If an external keyboard or mouse is connected, disconnect these devices. An error has occurred in the memory that stores the Setup Utility settings. This error occurs when the memory content is changed through some inadvertent operation by a program or other function. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. If the problem persists, the internal clock battery may need to be replaced. The date and time setting are incorrect. Run the Setup Utility and set the date and time correctly. If the problem persists, the internal clock battery may need to be replaced. Startup has failed repeatedly, so the Setup Utility settings have been returned to their default values, and the computer has been booted. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. Write down the error details and press F2 to run the Setup Utility. (The processing speed depends on the application software used, so this operation may not cause the processing speed to increase. ) If operations slow down during streaming playback, try changing the number of colors of the display. You can set the date and time using the following menu: [start] - [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time] If you continue to experience problems, the internal battery maintaining the clock may need to be replaced. Contact your technical support office ( page 45). When the computer is connected to a LAN, confirm the date and time of the server. This computer will not correctly recognize the date and time starting from the year 2100 A. D. Even when a password has been set in the Setup Utility, [Enter Password] does not appear when the computer resumes from the standby or hibernation mode. If you want to use the security function when using the standby or hibernation mode, use the Windows password as follows: 1 Select the account to change in [start] - [Control Panel] - [User Accounts] and set the password. 2 Add the check mark for [Prompt for password when computer resumes from standby] in [Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced]. This means a floppy disk that dose not contain system startup information has been left in the floppy disk drive. Remove the floppy disk, and press any key. This message may appear when certain USB devices are connected. [. . . ] and Alaska. DIAL TOLL FREE: 1-800-LAPTOP5 Correspondence requesting product information should be sent to: Panasonic Computer Solutions Company 50 Meadowlands Parkway, Panazip 2F-5, Secaucus, NJ 07094 45 Appendix * * * LIMITED WARRANTY For Canada PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY Coverage ­ Panasonic Canada Inc. ("PCI") warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified. Scope of Coverage Whole Product (except Batteries), AC adaptor and CD-ROM (if factory installed) Batteries, CD-ROM (unless factory installed), Port Replicator, Extra Memory Modules and all other Peripherals, Options and Accessories Period of Coverage Three (3) Years from Date of Original End User Customer Purchase One (1) Year from Date of Original End User Customer Purchase Type of Failure Coverage Defective Materials or Workmanship Defective Materials or Workmanship Remedy ­ In the event of a warranty claim, contact PCI's representatives within the applicable warranty period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A. M. (excluding holidays) for instructions on how to obtain service. [. . . ]