User manual PANASONIC CF-61XXXBAE

[. . . ] 5 Panasonic Hand Writing (Touch Pad) Windows 98 . . . . . 10 Standby/Hibernation Functions . . . . . . . . . . . . . . . . . . . . . 12 Security Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Computing On the Road . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not set [SuperDisk Operation] to [Disable] with the Setup Utility while a disk is in the SuperDisk drive. The disk will not be able to be removed by pressing the eject button. ( page 70) When the computer is turned on or during a reboot, a sound like the rotating of a motor will be audible several times. During the initial 10 seconds after inserting a SuperDisk or during data access, a shrill noise may be produced. This is not a malfunction. Installing/Removing a SuperDisk Drive page 31 Formatting the Disk It may take about 10 minutes to format the SuperDisk. Because of this, be sure to disable the power saving function beforehand so as not to enter the power saving mode while formatting the SuperDisk. CAUTION An error may occur later in the process of formatting a write-protected medium. To prevent this, be sure to format the medium after confirming beforehand that the write-protect state has been changed. DISKCOPY command does not support the SuperDisk. When MS-Backup is executed, the message "No Controller board detected" may be displayed. When an error message is displayed, click [OK], then continue running the MS-Backup program. SuperDiskTM Drive Software Preparation Windows 98 37 If the check mark is added for [Auto insert notification] under [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [Disk drives] - [MATSHITA LS-120 XXXX] - [Settings] - [Options], after entering the standby or hibernation mode, the computer may not function properly. In this case, delete the check mark for [Auto insert notification]. PC Cards Your computer has two PC Card slots. 2 Type [c:\util\drivers\pccard\setup. exe], press [OK], then follow the on-screen instructions. NOTE Do not use the Control Panel Icon labeled [PC Card (PCMCIA)]. This Control Panel will no longer function. Instead, use the Control Panel Icon labeled [Card Executive 2. 0 for NT] when checking on the status of the PC Cards in your system. RAM Module Use a RAM module meeting the RAM module specifications below. If a module is used that does not meet the specifications, there are cases in which data may become unusable or the computer may not operate properly. RAM module specifications 144 pins, SO-DIMM, 3. 3 V, SDRAM, PC100 Compliant Only a RAM module designed for PC100 can be added. 41 CAUTION RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. In addition, it is easy to damage the RAM modules or internal components of the computer. Therefore, when installing or removing a RAM module, handle the module with extreme care. Installing/Removing the RAM Module Memory Cover 2 1 Power off your computer ( "Starting Up/Shutting Down") Do not shut down using the standby or hibernation mode. 2 Remove the memory cover after removing the screw holding it in place CAUTION Turn the computer over and use a screwdriver to remove the screw. Do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter. Doing so has been known to cause damage, fire or electric shock. RAM Module Slot 3 2 RAM Module Hooks Installing the RAM module Slide in the module at an angle. 2 Snap the module into place by pushing down on it. [. . . ] A blue background appears on the screen with the MPEG image The CD-ROM/DVD-ROM drive vibrates a lot The disc tray does not close Emergency Hole Did you open the CD-ROM/DVD-ROM drive or remove the MPEG disc while it was operating?Re-insert the MPEG disc and close the CD-ROM/DVD-ROM drive. Set the [CD Drive Speed] to [Low] in the Setup Utility. ( page 58) Did you touch the eject button when you close the tray? Dealing With Problems (Advanced) Network Unable to connect to a network When using the computer as a network computer, some additional settings may have to be made depending on the usage conditions. [. . . ]