User manual PANASONIC CF-63XXXAAE

[. . . ] 8 Panasonic Hand Writing Windows 95 . . . . . . . . . . . . . 10 Suspend/Hibernation Functions . . . . . . . . . . . . . . . . . . . 12 Security Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Computing On The Road. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not allow the battery connector to touch any portion of the computer. When attaching the cover; Be careful not to get your fingers caught in the cover. Using a Multimedia Pocket Device You may use an optional CD-ROM pack (CF-VCD271), DVD-ROM drive pack (CFVDD272) or Superdisk drive pack (CF-VFS271) by removing your floppy disk drive from the multimedia pocket. For more information, please read the manual that accompanies the CD-ROM pack, DVD-ROM drive pack or Superdisk drive pack. 30 Installing/Removing a Multimedia Pocket Device 1 Cover Power off your computer ( "Starting Up/Shutting Down") Do not shut down using the suspend or hibernation mode. 2 Latch MP Release Button Removing the device Turn your computer over and open the cover by sliding the latch. 2 Firmly press the MP release button. The device will eject slightly. Remove the device by holding both sides of the device. CAUTION Please handle the device as shown (holding both sides). Also, do not apply excessive downward force on the device. The projections at the bottom of a device become deformed. 2 Installing the device Gently insert the device into the multimedia pocket by pushing on both corners until it clicks into place. CAUTION Do not install the device upside-down. The bottom of the drive may become disfigured. Install the device with the black plastic side on top. (If a label is attached, install the device with the label side on top. ) 3 Turn your computer on NOTE When the CD-ROM pack or DVD-ROM drive pack is installed: If the vibration of the CD-ROM or DVD-ROM drive is excessive, set the [CD-ROM /DVD-ROM Drive Speed] to [Low] in the Setup Utility. Using a Multimedia Pocket Device Parallel Port 31 Using the Floppy Disk Drive as an External Drive You may use the floppy disk drive as an external drive that is connected through the parallel port, by using an optional FDD cable (CF-VCF271). In the operating instructions for the FDD cable (CF-VCF271), directions are given to turn the power off before connecting the floppy disk drive by using the cable, but with this computer, the floppy disk drive can be attached or removed while the power is on. CAUTION Do not move the drive while accessing data on the floppy disk. Firmly hold both sides of the drive when removing a disk. (To next page) Using PC Cards PC Card Utility Program Windows NT 33 About Phoenix Card ExecutiveTM 2. 0 for Windows NT® When using a Windows NT® model, confirm that Phoenix Card ExecutiveTM 2. 0 for Windows NT® is installed. If [Card Executive 2. 0 for NT] is displayed in the [Control Panel], this indicates that the program is installed. If Phoenix Card ExecutiveTM 2. 0 for Windows NT® has been uninstalled, or Windows NT® Service Pack has been reinstalled, reinstall Phoenix Card ExecutiveTM 2. 0 for Windows NT® . 1 Select [Start] - [Run]. 2 Type "c:\util\drivers\pccard\setup. exe", press [OK], then follow the on-screen instructions. Adding Memory CAUTION Use a RAM module meeting the RAM module specifications below. If a module is used that does not meet the specifications, there are cases in which data may become unusable or the computer may not operate properly. RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. In addition, it is easy to damage the RAM modules or internal components of the computer. Therefore, when installing or removing a RAM module, handle the module with extreme care. 34 Installing/Removing the RAM Module 1 2 RAM Module Power off your computer ( "Starting Up/Shutting Down") Do not shut down using the suspend or hibernation mode. Remove the cover ( page 28) 3 Installing the RAM module Slide in the module at an angle. 2 Snap the module into place by pushing down on it. 2 RAM module specifications 144 pins, SO-DIMM, 3. 3 V, SDRAM Hooks Removing the RAM module Open the left and right hooks. 2 Gently remove the RAM module from the slot. 2 4 Put the cover back into place( page 29) Port Replicator A port replicator is available as an option (CF-VEB272A). This device eliminates the hassles of having you connect/disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone, microphone, or external display, etc. The port replicator connects to the expansion bus connector on the back of your computer. [. . . ] In some circumstances, if a PS/2 external mouse with a serial interface conversion function is connected to the port, it may not operate normally. Make sure the card is properly inserted. Confirm that the card conforms to the PC Card Standard. Note that after a driver is installed, the computer must be rebooted. [. . . ]