User manual PANASONIC CF-71DJXXXXX

[. . . ] ® Personal Computer Reference Manual CF-71 Series Contents 95 Key Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Panasonic Hand Writing (Touch Pad) . . . . . . . . . . . . . . . . . . . . . 4 Suspend/Hibernation Functions . . . . . . . . . . . . . . . . . . . . . . [. . . ] 3 Type [c:\util\drivers\pccard\setup. exe], press [OK], then follow the on-screen instructions. CAUTION After PhoenixCard ManagerTM for Windows® 95 has been installed, make sure to power off the computer before installing or removing the card. Also, do not use the suspend or hibernation functions if the card is installed. NOTE When running the power conservation function with the sound chip set, there may be no sound output. In this case, the following setting needs to be made. In [Control Panel] - [Power] - [OPL3-SAx power management], set [Non Power page 41) Save mode] then press [Apply]. ( Uninstalling When you decide not to use the ZV card, be sure to perform the uninstall procedure. 1 Uninstall PhoenixCard ManagerTM for Windows® 95 in [Start] - [Settings] - [Control Panel] - [Add/Remove Programs]. 2 Restart the computer. 3 Select [PC Card (PCMCIA)] in [Start] - [Settings] - [Control Panel]. 4 Press [Next] at the display for the [Display Driver Wizard for PC Cards (PCMCIA)], press [Next] again and then press [Finish]. 5 Shut down the computer by following the on-screen instructions. Adding Memory RAM Module CAUTION Use a RAM module meeting the RAM module specifications below. If a module is used that does not meet the specifications, there are cases in which data may become unusable or the computer may not operate properly. RAM modules are extremely sensitive to static electricity. There are cases where static electricity generated by the human body has adversely affected such modules. In addition, it is easy to damage the RAM modules or internal components of the computer. Therefore, when installing or removing a RAM module, handle the module with extreme care. 25 Installing/Removing the RAM Module 1 Cover Power off your computer ( CAUTION "Starting Up/Shutting Down") Do not shut down using the suspend or hibernation mode. Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. 2 2 Remove the memory cover after removing the screw holding it in place Turn the computer over and use a screwdriver to remove the screw. CAUTION Do not touch the terminals or internal components, insert objects other than the module, or allow foreign particles to enter. Doing so has been known to cause damage, fire or electric shock. RAM Module Slot 3 2 Installing the RAM module Slide in the module at an angle and snap the module into place by pushing down on it. RAM module specifications 144 pins, SO-DIMM, 3. 3 V, SDRAM RAM Module Hooks Removing the RAM module Open the left and right hooks. 2 Gently remove the RAM module from the slot. 2 4 2 Put the cover back into place, then fasten the screw Port Replicator A port replicator is available as an option (CF-VEB711). This device eliminates the hassles of having you connect/disconnect the various cables when carrying your computer around and allows a variety of peripherals to be connected including a headphone or microphone, etc. The port replicator connects to the expansion bus connector on the bottom of your computer. For more detailed information, please refer to the operation manual of the port replicator. 26 CAUTION When the computer and the port replicator are connected, both PC Card slots (total of four slots) cannot be used simultaneously. Before connecting the port replicator, set [Disable] for [Internal CardBus Controller] with the Setup Utility to disable the PC Card slots on the computer side. Using a Printer 1 Power off your computer ( CAUTION Do not install or remove peripherals while your computer is in the suspend or hibernation mode; abnormal operation may result. "Starting Up/Shutting Down") Do not shut down using the suspend or hibernation mode. 27 Parallel Port 2 Connect the printer to your computer 3 Turn on the printer, then turn on your computer with the LCD panel opened 4 Setting your printer Go to [My Computer] - [Printers]. Find your printer's icon, double-click on it, and click [File] - [Set As Default]. If no icon is available, select [Add Printer] and then follow the on-screen instructions. NOTE You may need to install a driver for your printer. [. . . ] If the device still does not work, try restarting the computer. Make sure the card is properly inserted. Confirm that the card conforms to the PC Card Standard. Note that after a driver is installed, the computer must be rebooted. [. . . ]