User manual PANASONIC CF-73N3LTSKM

[. . . ] Personal Computer OPERATING INSTRUCTIONS Model No. CF-73 Series Getting Started Appendix Troubleshooting Operation Contents Getting Started XP Read Me First. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Names and Functions of Parts . . . . . . . . . . . . . . . . . . . . . . . . 9 First-time Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Reference Manual · Read Me First · Key Combinations · LED Indicators Operation Starting Up/Shutting Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 0280: Previous boot incomplete Startup has failed repeatedly, so the Setup Utility settings have been returned to their default - Default configuration used values, and the computer has been restarted. Run the Setup Utility and load the default values, then change the settings to the appropriate values as needed. 1 0613: Serial Port* configura- I/O address and IRQ settings are in conflict. tion changed Run the Setup Utility and change the settings in [Advanced] menu so there is no port 0614: Serial Port*1 config. - device disabled *1 The port name, such as A or B, is displayed, indicating the conflicting ports. Error Code/Message 0211: Keyboard error 0251: System CMOS checksum bad - Default configuration used Press <F1> to resume, <F2> to Setup Operating System not found Troubleshooting Write down the error details and press F2 to run the Setup Utility. Confirm the settings, and change the settings to the appropriate values as needed. The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from. If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and change it to another if not. If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility. · If the hard disk is recognized, perform the reinstallation procedure. · If not, contact Panasonic Technical Support. If a device is connected to the USB port, disconnect the device, or run the Setup Utility and set [Legacy USB Support] in [Advanced] menu to [Disable]. How to run the Setup Utility 1 Turn on or restart the computer. 2 Press F2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. 24 Dealing with Problems (Summary) When a problem occurs, refer to this page. The "Reference Manual" also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact Panasonic Technical Support. You can use the PC Information Viewer to check the computer's usage status. ( "Dealing with Problems (Advanced)") Starting Up The power indicator or battery indicator is not lit The computer does not operate when a USB device is connected [Enter Password] is displayed POST Startup Error(s) is displayed Windows startup, or an operation is extremely slow Check the cable connection for the AC adaptor. Check to see if a fully charged battery is properly inserted. Remove the battery pack and disconnect the AC adaptor, then connect them again. The computer may not operate when certain USB devices are connected. Disconnect the USB device, or set [Legacy USB Support] to [Disable] in [Advanced] menu of the Setup Utility. [. . . ] Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the balance of the original period of warranty coverage. No Coverage ­ This Limited Warranty does not cover products purchased outside Canada. Neither does it cover damage to, failure of, or defects in a product or accessory through mishandling, improper installation, abnormal use, misuse, neglect, accident, introduction of liquid or other foreign matter into the product, alteration or servicing by anyone not authorized by PCI, or act of God. IF YOU SHIP THE PRODUCT FOR WARRANTY SERVICE Carefully pack the product, preferably in the original carton. [. . . ]