User manual PANASONIC CF-T1R64ZZKM

[. . . ] 21 Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Troubleshooting List of Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Dealing with Problems (Summary). . . . . . . . . . . . . . . . . . . 29 Reinstalling Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For instructions on settings for wireless LAN and cautions during use, click [start][Reference Manual], and refer to "Wireless LAN". Before using a wireless LAN, turn the wireless LAN on using the following method (at the time of purchase, the wireless LAN is set to [Wireless Off]). 1 Double-click (When the wireless LAN is off) on the notification area. The icon will turn to (yellow icon) / (red icon) / (green icon). Do not use wireless LAN on airplanes, in hospitals, or in other locations where wireless LAN signals may affect the operation of devices in the vicinity. Abide by instructions regarding use in airplanes and hospitals. Enable/disable wireless LAN standard IEEE802. 11a (802. 11a) In some countries, communication using IEEE802. 11a (5 GHz wireless LAN) standard is restricted by law. Comply with the laws in the country concerned. ( page 3) 1 Click the icon (when the wireless LAN is on) or the icon (when the wireless LAN is off) on the notification area. 2 To disable 802. 11a: Click [Disable 802. 11a]. To enable 802. 11a: Click [Enable 802. 11a]. Even when 802. 11a is enabled or disabled, or will not change. 27 Operation List of Error Codes When turning on the computer, if one of the following error codes or messages is displayed, follow the instructions shown below. If the problem persists, or if the error code or message displayed is not shown here, contact your technical support office ( page 45). The "Reference Manual" also contains detailed information. If a problem appears to be related to a software application, read the software related manual. If you still cannot troubleshoot the problem, contact your technical support office ( page 45). You can use the PC Information Viewer to check the computer's usage status. ( "Troubleshooting") Starting Up The power indicator or battery indicator is not lit The computer does not operate when a USB device is connected [Enter Password] is displayed POST Startup Error(s) is displayed Windows startup, or an operation is extremely slow Check the cable connection for the AC adaptor. Check to see if a fully charged battery is properly inserted. Remove the battery pack and disconnect the AC adaptor, then connect them again. The computer may not operate when certain USB devices are connected. Disconnect the USB device, or set [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. Input your Supervisor Password or User Password. If you have forgotten it, contact your technical support office ( page 45). [. . . ] Scope of Coverage Whole Product (except Batteries), AC adaptor and CD-ROM (if factory installed) Batteries, CD-ROM (unless factory installed), Port Replicator, Extra Memory Modules and all other Peripherals, Options and Accessories Period of Coverage Three (3) Years from Date of Original End User Customer Purchase One (1) Year from Date of Original End User Customer Purchase Type of Failure Coverage Defective Materials or Workmanship Defective Materials or Workmanship Remedy ­ In the event of a warranty claim, contact PCI's representatives within the applicable warranty period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A. M. (excluding holidays) for instructions on how to obtain service. A purchase receipt or other proof of date of original purchase is required before warranty service is performed. Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on an exchange basis. [. . . ]