User manual PANASONIC CF-VFS712W

[. . . ] 16 Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Reference Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 RAM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Useful Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not expose the DVD-ROM & CD-R/RW drive to excessive smoke that may leave a residue, e. g. Doing so could shorten the life of the drive lens. When opening/closing the disc cover When the computer is on, be sure to use the open lever on the left side of the computer or perform the ejecting operation through Windows. · When a using B's Recorder/B's CLiP: "B's Recorder/B's CLiP" When closing the disc cover, press down near the power indicator (position of the arrow) to ensure that the cover is locked. Do not access the drive until after the disc cover is closed and the DVD-ROM & CD-R/ RW drive status indicator is off. To remove a disc when the disc cover cannot be opened or when the computer is powered off: Insert a pointed object (e. g. , the bent-out tip of a paper clip, or the tip of a ballpoint pen) into the emergency hole (C), and then move in the direction of the arrow. The disc cover can be opened up to an angle of 70 degrees. Do not force the cover open any further. touches the disc cover and accidentally opens wider than 70 degrees, pull it forward slowly until the stopper holds the cover in its proper position. Do not leave the disc cover in the open position or touch the lens. Under some conditions, dust may build up on the lens, or on a disc. This may result in a read or write malfunction. Press <F1> to resume, <F2> to Write down the error details and press F2 to run the Setup Utility. Confirm the Setup settings, and change the settings to the appropriate values as needed. Operating System not found The OS is not properly installed on the floppy disk or the hard disk that you are trying to boot from. If the computer cannot be booted from the floppy disk, check the floppy disk drive to ensure that the disk is in fact bootable, and change it to another if not. If the computer cannot be booted from the hard disk, confirm whether the hard disk is properly recognized in [Information] menu of the Setup Utility. If the hard disk is recognized, perform the reinstallation procedure. If not, contact your technical support office. If a device is connected to the USB port, disconnect the device, or run the Setup Utility and set [Legacy USB Support] in [Advanced] menu to [Disable]. Error Code/Message 0211: Keyboard error 0251: System CMOS checksum bad - Default configuration used How to run the Setup Utility 1 Restart the computer. 2 Press F2 while [Panasonic] boot screen is displayed soon after the computer begins the startup procedure. Troubleshooting 28 Dealing with Problems (Summary) When a problem occurs, refer to this page. The "Reference Manual" also contains detailed information. [. . . ] and Alaska. DIAL TOLL FREE: 1-800-LAPTOP5 Correspondence requesting product information should be sent to: Panasonic Computer Solutions Company 50 Meadowlands Parkway, Panazip 2F-5, Secaucus, NJ 07094 45 Appendix * * * LIMITED WARRANTY For Canada PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY Coverage ­ Panasonic Canada Inc. ("PCI") warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under normal use, subject to the terms set forth below, during the period of warranty coverage specified. Scope of Coverage Whole Product (except Batteries), AC adaptor and CD-ROM (if factory installed) Batteries, CD-ROM (unless factory installed), Port Replicator, Extra Memory Modules and all other Peripherals, Options and Accessories Period of Coverage Three (3) Years from Date of Original End User Customer Purchase One (1) Year from Date of Original End User Customer Purchase Type of Failure Coverage Defective Materials or Workmanship Defective Materials or Workmanship Remedy ­ In the event of a warranty claim, contact PCI's representatives within the applicable warranty period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A. M. (excluding holidays) for instructions on how to obtain service. [. . . ]