User manual PANASONIC CF-Y2

[. . . ] OPERATING INSTRUCTIONS Personal Computer Model No. CF-Y2 Series Getting Started Appendix Troubleshooting Operation Contents XP Getting Started Page Read Me First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Names and Functions of Parts . . . . . . . . . . . . . . . . . . . . . . 10 First-time Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Operation Starting Up/Shutting Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This will restore the Setup Utility's settings to their default values (except the password settings, System Date, and System Time). Then, the Setup Utility must be run once again for you to input the appropriate operating environment settings. (The processing speed depends on the application software used, so this operation may not cause the processing speed to increase. ) If operations slow down during streaming playback, try changing the number of colors of the display. If you install resident software after purchasing this computer, disable that resident software. You can set the date and time using the following menu: [start] - [Control Panel] - [Date, Time, Language, and Regional Options] - [Date and Time] If you continue to experience problems, the internal battery maintaining the clock may need to be replaced. Contact your technical support office ( page 50). When the computer is connected to a LAN, confirm the date and time of the server. This computer will not correctly recognize the date and time starting from the year 2100 A. D. Even when a password has been set in the [Security] menu of the Setup Utility, [Enter Password] does not appear when the computer resumes from the standby or hibernation mode. If you want to use the security function when using the standby or hibernation mode, use the Windows password as follows: 1 Select the account to change in [start] - [Control Panel] - [User Accounts] and set the password. 2 Add the check mark for [Prompt for password when computer resumes from standby] in [Control Panel] - [Performance and Maintenance] - [Power Options] - [Advanced]. This means a floppy disk that does not contain system startup information has been left in the floppy disk drive. Remove the floppy disk, and press any key. This message may appear when certain USB devices are connected. Remove the USB device, or set [Legacy USB Support] in the [Advanced] menu of the Setup Utility to [Disable]. If the message still appears even after trying the above measures, this may be an indication that some type of hard disk failure has occurred. If you have created a password reset disk ( page 15), a message is displayed when you fail to correctly enter the password. Follow the message's instructions and set the password again by using the password reset disk. If you have not created a password reset disk, after reinstalling, setup Windows and then set the password again. The date and time are incorrect When resuming from the standby or hibernation mode, [Enter Password] does not appear even if a password has been set in the Setup Utility Troubleshooting When "Remove disks or other media. Press any key to restart" (or a similar message) is displayed When the administrator password is forgotten 30 Starting Up (continued) When the previous item is not the cause Press F9 in the Setup Utility ( "Setup Utility"). This will restore the Setup Utility's settings to their default values (except the password settings). Check a disk error using the following procedure. [. . . ] Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the balance of the original period of warranty coverage. No Coverage ­ This Limited Warranty does not cover products purchased outside Canada. Neither does it cover damage to, failure of, or defects in a product or accessory through mishandling, improper installation, abnormal use, misuse, neglect, accident, introduction of liquid or other foreign matter into the product, alteration or servicing by anyone not authorized by PCI, or act of God. IF YOU SHIP THE PRODUCT FOR WARRANTY SERVICE Carefully pack the product, preferably in the original carton. [. . . ]