User manual PANASONIC CQ-DF600

[. . . ] Keep screwdrivers and other metallic objects away from the disc mechanism and disc. Lithium battery (Type: CR2025) When Washing Your Car Do not expose the product, including the speakers and CDs, to water or excessive moisture. This could cause electrical shorts, fire, or other damage. Service This product is made of precision parts. Do not attempt to disassemble or adjust any parts. [. . . ] Default: 0 Setting range: 12 dB to +12 dB (in 2 dB step) Press [VOLUME] (SEL: Select). Turn [VOLUME]. q : Increased w : Decreased Balance You can adjust the sound balance among the right and left speakers. Default: CNT (Center) Setting range: 15 levels each Press [VOLUME] (SEL: Select). Turn [VOLUME]. q : Right enhanced w : Left enhanced Fader You can adjust the sound balance among the front and rear speakers. Default: CNT (Center) Setting range: 15 levels each Press [VOLUME] (SEL: Select). Turn [VOLUME]. q : Front enhanced w : Rear enhanced 22 CQ-DF600 CQ-DF600 23 E N G L I S H 15 Installation Preparation Before installation, check the radio operation with antenna and speakers. Disconnect the cable from the negative () battery terminal (see caution below). Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30. Remove Mounting Collar q and Trim Plate r from the main unit temporarily, which are already mounted at shipment. Supplied Hardware No. q Item Mounting Collar Mounting Bolt (5 mm) Power Connector Trim Plate Lock Cancel Plate Rear Support Strap Tapping Screw (5 mm x 16 mm) Hex. Nut (5 mm) Diagram Q'ty 1 1 1 1 2 1 1 1 Caution: We strongly recommend that you wear gloves for installation work to protect yourself from injuries. Place the face plate into the case and take it with you when you leave the car. w (c) Pull out the face plate on the right side of the unit. w Remove the trim plate r with a screwdriver. Screwdriver Install Removable Face Plate 1 w r Trim Plate 2 q Slide the left side of the removable face plate in place. w Press the right end of removable face plate until "click" is heard. q e Pull out the unit while pushing down the lock lever with the lock cancel Plate t. 1 Insert Insert the tab end in the outer groove. t Lock Cancel Plate Caution: This face plate is not waterproof. Do not expose it to water or excessive moisture. Do not remove the face plate while driving your car. Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level. Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth. To avoid damaging the front panel, do not push it down or place objects on it while it is open. "Click" 2 Pull out r Remove the unit pulling with both hands. Caution: Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth. 26 CQ-DF600 CQ-DF600 27 E N G L I S H 19 Electrical Connections Cable Wiring Diagram Caution: This unit is designed for use in a car having a 12-volt negative ground battery system. To prevent damage to the unit, be sure to follow the connection diagram below. Strip about 5 mm of the lead ends for connection. [. . . ] aMove to an area where receivable stations number is maximum, and try presetting. The contact of the battery lead is poor, or the battery lead is not always powered. aMake sure that the battery lead is connected securely, and preset stations again. Poor reception or noise Sound is not generated The number of auto preset stations is less than 6. The demonstration screen displayed and no operable Preset stations cannot be stored. Noise CD Problem Possible cause a Possible solution The disc is inserted upside down. There is a flaw or foreign material on the disc. [. . . ]