User manual PANASONIC CQ-DF783U

[. . . ] E N G L I S H 17 Audio Settings POWER MENU E N G L I S H VOL [SEL] (select) SOURCE SEL NUMBER MUTE # 2 SCAN [VOL "] [VOL #] 18 1 RAND 3 REP 4 5 8 0 6 9 5 1 Press [SEL]. (Push. ) 2 (Press [VOL "] or [VOL #] [VOL #] on the remote control unit. ) Turn [VOL]. 7 [VOL "] 6 BAND SET DISP Car Audio Volume Default: 18 Setting range: 0 to 40 Select [VOL "]: Increases the volume. [VOL #]: Decreases the volume. Select Bass and Treble You can adjust the bass and treble sound. Default: BAS (bass) 0 dB TRE (treble) 0 dB Setting range: j12 dB to i12 dB (by 2 dB) Select [VOL "]: Increases the bass. [VOL #]: Decreases the treble. Note: Press [DISP] (display) to return to the regular mode. [. . . ] If the replacement fuse fails, contact your nearest Panasonic Servicenter for service. Do not attach any seals or labels to your discs. Do not write on the disc label in a heavy pen or ballpoint pen stroke. Product Servicing If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Servicenter. The product should be serviced only by a qualified technician. 42 CQ-DF783/DFX403U CQ-DF783/DFX403U 43 E N G L I S H 29 Installation Guide Identify All Leads WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. Speakers Identify the car speaker leads. There are two leads for each speaker which are usually color coded. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 30 Installation Hardware No. 1 2 3 4 5 6 7 8 9 Item Mounting collar Hex. [. . . ] Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level. 2 Pull out. 4 Remove the unit by pulling with both hands. Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth. To avoid damaging the front panel, do not push it down or place objects on it while it is open. 48 CQ-DF783/DFX403U CQ-DF783/DFX403U 49 E N G L I S H 35 Electrical Connections Caution: This product is designed to operate with a 12 V DC, negative ground battery system. To prevent damage to the unit, be sure to follow the connection diagram below. [. . . ]