User manual PANASONIC CQ-DFX150

[. . . ] We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family. E N G L I S H When Washing Your Car Do not expose the product, including the speakers and CDs, to water or excessive moisture. This could cause electrical shorts, fire, or other damage. CQ-C3400/C3300U Removable Full Front MP3 WMA CD Player/Receiver with CD Changer Control CQ-C3200/C3100U Removable Full Front CD Player/Receiver with CD Changer Control Note: Please refer to page 9 for information on differences in each model. CAUTION: THIS PRODUCT IS A CLASS I LASER PRODUCT. [. . . ] The volume can also be adjusted directly using [VOLUME] on the main unit. (page 23) Subwoofer Level You can change the subwoofer volume level. Default: 0 dB Setting range: MUTE (subwoofer mute), j6 dB to i6 dB (by 2 dB) Select CQ-C3400U [VOLUME "]: Increased [VOLUME #]: Decreased Subwoofer Low Pass Filter (LPF) You can select the upper limit frequency of the sound from subwoofer. Default: 80 Hz Setting range: 120 Hz/80 Hz Select [VOLUME "]: 120 Hz [VOLUME #]: 80 Hz Mute/Attenuation You can select mute or attenuation when [MUTE] is pressed. (page 23) Default: MUTE [VOLUME "]: Decrease 10 steps (Attenuation) [VOLUME #]: No sound (Mute) CQ-C3400/3300/3200/3100U 34 CQ-C3400/3300/3200/3100U 35 E N G L I S H 17 Security Setting 1 Press and hold [VOLUME] (SEL: select) for more than 2 seconds. 2 Turn [VOLUME]. (Press ["] or [#] on the remote control unit. ) [SEL] (Select) E N G L I S H POWER MENU SOURCE SEL NUMBER 18 VOL MUTE # 2 SCAN 1 RAND 3 REP ["] [#] ["] (Press and hold. ) 2 sec. [#] 4 7 6 5 8 0 6 9 5 BAND SET DISP [DISP] (Display) Car Audio Security Function Allows you to activate the anti-theft function when leaving your car. Default: ON ["]: Security function is activated. [#]: Security function is not activated. Note: Press [DISP] (display) to return to the regular mode. If no operation takes place for more than 7 seconds in security setting, the display returns to the regular mode. Security Function When the key in the ignition is turned OFF Security message will be displayed. The panel removal alarm will be active. (page 45) When the front panel is removed The security indicator blinks. The wiring of the speaker lines are not correct, or a break or poor contact arises. You cannot operate the unit while the demonstration screen appears. Replace the speaker with new one. Perform the speaker wiring in accordance with the wiring diagram. The demonstration screen displayed and no operable. Press [DISP] (display) to end the demonstration screen. q Radio Poor reception or noise Antenna installation or wiring of antenna cable is faulty. Check whether the antenna mounting position and its wiring are correct. In addition, check to see whether the antenna ground is securely connected to the chassis. If the demonstration screen appears Check the battery wiring in accordance frequently, there is a possibility that with the wiring diagram. poor contact or wrong wiring arises between the battery lead of the unit and the battery cable of the car. (The battery lead should be always powered. ) Some operations are not executable Read the operating instructions in particular modes such as menu carefully and cancel the mode. the unit is still out of order, consult the dealer. Some operations are not executable. No power is supplied to the antenna Check the wiring of the antenna battery amplifier (when using a film lead. The number of auto preset stations are less than 6. The number of receivable stations are less than 6. Move to an area where receivable stations number is maximum, and try presetting. [. . . ] To prevent damage to the unit, be sure to follow the connection diagram below. Remove approximately 1/4q (5 mm) of protective covering from the ends of the leads before connecting. Do not insert the power connector into the unit until the wiring is completed. Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. [. . . ]