User manual PANASONIC CQ-DFX983

[. . . ] We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family. E N G L I S H When Washing Your Car Do not expose the product, including the speakers and CDs, to water or excessive moisture. This could cause electrical shorts, fire, or other damage. CQ-C5410/C5310U Removable Full Front MP3 WMA CD Player/Receiver with CD Changer Control CQ-C5210/C5110U Removable Full Front CD Player/Receiver with CD Changer Control Note: Please refer to page 9 for information on differences in each model. CAUTION: THIS PRODUCT IS A CLASS I LASER PRODUCT. [. . . ] The volume can also be adjusted directly using [VOLUME] on the main unit. (page 23) Note: Only buttons [2] to [6] can be used to preset the adjusted SQ. An adjusted SQ cannot be preset in button [1]. While the SQ adjustment mode is established, only adjustments are performed, and even if the adjustment mode is exited without presetting an adjusted effect, what has been set will be reflected as the current SQ until another SQ is selected. Even when the SQ presets are adjusted, the display which appears when the settings are called remains unchanged. The SQ adjustment mode can be established also by pressing [SQ] for more than 2 seconds. SQ Adjustment You can adjust the characteristics of the currently selected sound type (SQ). It is also possible for a maximum of 5 different adjusted SQ to be preset. Adjustable frequency: 60 Hz, 160 Hz, 400 Hz, 1 kHz, 3 kHz, 6 kHz, 16 kHz Setting range: j12 dB to i12 dB (by 2 dB) Setting of SQ, bass/treble and volume are influenced one another. If the influence mentioned above causes distortion to the audio signal, readjust bass/treble or volume. Select 36 CQ-C5410/5310/5210/5110U CQ-C5410/5310/5210/5110U 37 E N G L I S H 19 Audio Settings (continued) 1 Press [VOLUME] (SEL: select). 2 Turn [VOLUME]. (Press [VOL "] or [VOL #] on the remote control unit. ) E N G L I S H [SEL] (Select) POWER MENU 20 SOURCE SEL NUMBER [VOL "] VOL MUTE # 2 SCAN [VOL #] 3 REP 1 RAND 4 5 8 0 6 9 5 [VOLUME "] [VOLUME #] (Push. ) 7 6 BAND SET DISP [DISP] (Display) Car Audio Balance/Fader You can adjust the sound balance among the front, rear, right and left speakers. Default: BAL (balance) CNT (center) FAD (fader) CNT (center) Setting range: 15 levels each Select [VOLUME "]: Right enhanced [VOLUME #]: Left enhanced Select [VOLUME "]: Front enhanced [VOLUME #]: Rear enhanced Subwoofer Level You can change the subwoofer volume level. Balance/fader setting is not appropriate. There is a break, a short circuit, poor contact or wrong wiring regarding the speaker wiring. The Power fails unintentionally The safety device works. Call the store where you purchased the unit, or your nearest Panasonic Servicenter. The speaker channels are reversed between right and left. The speaker wiring is confused between right and left. Check the speaker wiring. E N G L I S H 24 If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. The contact of the ground lead is poor. Troubleshooting Tips Common Problem No power to the unit Possible cause The power cord (battery, ACC and ground) is connected in the wrong way. Noise is made in step with engine revolutions. No sound from speaker (s) Alternator noise comes from the car. Eliminate the cause of fuse blow out and replace the fuse with new one. [. . . ] To prevent damage to the unit, be sure to follow the connection diagram below. Remove approximately 1/4q (5 mm) of protective covering from the ends of the leads before connecting. Do not insert the power connector into the unit until the wiring is completed. Preout cord (front) Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. [. . . ]