User manual PANASONIC CQ-DP850

[. . . ] Secure all loose wires after installing the unit. Please carefully read the operating and installation instructions of the respective equipment before connecting it to this unit. 4 CQ-DP850 Installation Hardware (For Installation) No. 1 <YFC054C088ZA> Transportation Bracket Removal Be sure to remove the transportation brackets before use (installation). Use round head screws (5 mmø x 8 mm) for installation. [. . . ] ¡Do not scratch the panel with fingernails or any hard objects. a Failure to observe the above may damage or break the glass on the surface of the touch panel. Installation Hardware (For Wiring) No. i Item Power Connector (ISO connector) Diagram Qty. 1 1 1 <YEAJ012891> o Reverse Extension Cord !0 Clip Connector !1 ISO Antenna Adapter 1 <YEAA33144> Note: ¡The number in parenthesis underneath each accessory part name is the part number for maintenance and service. ¡Accessories and their parts numbers are subject to modification without prior notice due to improvements. ¡Mounting Collar w is mounted on the main unit at shipment. ¡Use the supplied screws for installation exclusively. In case of losing any of them, please order the specific screw. CQ-DP850 English 4 5 Installation Guide English 5 Note: ¡The car model, installation conditions and combination of the units used may impose some restrictions on opening and closing the monitor as well as on the angle and position to which the monitor can be adjusted. (continued) Mounting and removing the Display Unit Mounting Procedures (A) (When using Mounting Collar w) IMPORTANT When this unit is installed in dashboard, ensure that there is sufficient air flow around the unit to prevent damage from overheating. Do not block any ventilation holes on the unit. q Insert the Mounting Collar w into the dash- q board, and bend the mounting tabs out with a screwdriver. w Establish the rear connection of the unit. After fixing Power Connector i, fix the rear of the unit to the car body by either method (a) or (b). e Insert the unit into Mounting Collar w. Secure the clamp plate of Mounting Collar w to the hook. w e r t Snapping point r Insert Trim Plate q. t After installation reconnect the negative (­) battery terminal. Method for Fixing the Rear of the Unit (a) Using the Rear Support Strap t. Fire wall of car (b) Using the Rubber Cushion (option) 3 mmø t Rear Support Strap Tapping Screw (option) (5 mmø x 16 mm) Hex. Nut (option) (5 mmø) To the unit r Mounting Bolt (5 mmø) Rubber Bushing (option) Rear Support Bracket (Provided on the Car) r Mounting Bolt (5 mmø) To the unit 6 CQ-DP850 Mounting Procedures (B) (When not using Mounting Collar w) Use the brackets supplied with your car when mounting this unit. Consult with a qualified servicing engineer or your dealer if other methods are required. CQ-DP850 English 8 9 Electrical Connections English (continued) Wiring Diagram 9 5 6 8 mmMA X CQ-DP850 (Rear) 1 2 3 4 FUSE 1 5 A >PBT< J A M- S A a Fuse (15 A) Refer fuse replacement to your nearest authorized Panasonic Service Centre. Do not try fuse replacement by yourself. (Black) (White) (R)(Red) (L)(White) (Yellow) (Black) (Red) q w Pre-Out Subwoofer connector (mono) To external amplifier. e Pre-Out Connector (rear) To external amplifier. Pre-Out Connector (centre) To external amplifier. t Video Input Terminal (AV1-IN) y Video Input Terminal (AV2-IN) Connect a VCR, camcorder, other brand's car navigation system, etc. (a page 18) Note: When an external device is connected to the system-up connector, the audio terminals, {(R)(Red), (L)(White)}, of AV2-IN are disabled. r Pre-Out Connector (front) To external amplifier. (R)(Red) AV-OUT (L)(White) (Yellow) Video Output Terminal (AV-OUT) Connect the rear monitor. (a page 16) CAMERA-IN (Yellow) Camera Input Terminal (CAMERA-IN) Connect a rear view camera. (a page 17) 10 CQ-DP850 RGB Connector To the Panasonic Car Navigation System. Radio Antenna Connector (RADIO ANT IN) !1 ISO Antenna Adapter (If needed) System-up Connector To external devices equipped with system-up connector. i Power Connector To power connector of the unit. REVERSE SIDE BRAKE Reverse Lead (Violet/white stripe) When connecting the rear view camera, use the reverse lead. Side Brake (Parking Brake) Connection Lead (Bright green) Be sure to wire the side brake (parking brake) for safety and preventing accidents. Navi Mute Lead (Orange) To navi mute lead of car navigation system. External Remote Control Lead (Brown/black stripe) When using a non-Panasonic external remote control, refer to the manufacture for their product before connecting. External Amplifier Control Power Lead (Blue/white stripe) To an external amplifier. Note: ¡Use the power control lead of the TV tuner for TV tuner connection. [. . . ] Note: ¡Use the power control lead of the TV tuner for TV tuner connection. ¡Connect both the power control lead of the TV tuner and the amplifier control connector of the external amplifier when the TV tuner and external amplifier are connected at the same time. Speakers B8 : Rear Left ­ B7 : Rear Left + B6 : Front Left ­ B5 : Front Left + B4 : Front Right ­ B3 : Front Right + B2 : Rear Right ­ B1 : Rear Right + Caution ¡Use ungrounded speakers only. Allowable input : 50 W or more Impedance : 4 ­ 8 ¡Distance between speaker and amplifier: 30 cm or more ¡Do not connect more than one speaker to one set of speaker leads. [. . . ]