User manual PANASONIC CQ-DPX303

[. . . ] For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www. eiae. org. > Find the model number and serial number on either the back or bottom of the unit. Please record them in the space below and retain this booklet as a permanent record of your purchase to help with identification in case of theft. MODEL NUMBER DATE PURCHASED CQ-DPX303U SERIAL NUMBER FROM 2 CQ-DPX303U Panasonic welcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. [. . . ] Music is lights R : Random Indicator played from all available CDs. · Press [6] (RDM) again to cancel. · Press and hold [6] (RDM) for more than 2 seconds all the available tracks on the current blinks R : Random Indicator disc play in a random sequence. · Press and hold [6] (RDM) for more than 2 seconds again to cancel Remote Control CA-RC500U (option) 15 CQ-DPX303U XM Control Preparation: Connect the XM receiver (XM DIRECT MODEL:XM-RVR-D-001) to the Unit CQ-DPX303U. XM satellite radio is available on a chargable basis. q XM Mode (When a XM receiver is connected. ) Press [MODE] to change to the XM mode. CLK r Channel Scan Press [SCAN], each channel in ascending order will be scanned sequentially and the display will blink for 5 seconds. Press [SCAN] again to stop scamming and the last channel will continue to broadcast. PWR ALM VOL PUSH SEL / SAT DISP CQ-DPX303U LOUD MODE DISC CD SCAN RPT RDM MUTE TUNE SEEK SCAN ILL BAND BASS/TREB/BAL/FADER 1 APM 2 3 4 5 6 w Band Press [BAND]. [CATEGORY] XM displays as follows, (Example) Satellite Radio after 2 seconds Indicator e Channel Selection Press [}]: Up Press [{]: Down Press and hold [}] or [{] for more than 2 seconds to change channels rapidly. XM Band Preset Number Channel Number after 5 seconds Channel Name Category Priority Setting and Selecting · Push the knob [SEL] for more than 2 seconds. (Push and hold) (without operation during 2 seconds. ) (when category is set ON. ) (without operation during 5 seconds. ) category name (interdisplay for 2 seconds. ) turn left (blinks) turn right (when category is set OFF. ) 16 CQ-DPX303U · When the display shows "CAT ON", Press [2] (}): Up Press [1] ({): Down 1 2 1 2 (without operation during 5 seconds. ) Category Name Press [2] or [1]. (Receiving) (Received) Category Name (interdisplay for 2 seconds. ) Push and hold the knob [SEL] for more than 2 seconds to resume the normal display. category on indicator Notes: CAT OFF: Every channel can be selected from every category. CAT ON: Only channels in the current category can be selected. a Connect the battery cable to the terminal that is always active. Much noise in FM stereo and monaural broadcasts. Preset station is reset. CD Trouble Cause/Step Disc is upside down. a Place disc in the correct direction with the label side up. a Clean disc, referring to the section on "Notes on Discs". A disc that has data other than CD-DA type is loaded. a Discs that have CD-DA type data should be used. a The unit may not successfully playback a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. Refer to instructions for the concerned devices for details. a Clean disc, referring to the section on "Notes on Discs". a The unit may not successfully playback a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. Refer to instructions for the concerned devices for details. Disc is in the CD compartment but no sound is made, or disc is ejected automatically. Sound skips, bad sound quality. caused by noise) 20 CQ-DPX303U CD (Continued) Trouble Cause/Step Mounting angle is over 30°. [. . . ] · Disconnect the cable from the negative terminal (see warning and caution below). q w e r t y u i Item Mounting Collar* Plain washer (5mmø) Spring Washer (5mmø) Hex. Nut (5mmø) Rear Support Strap Hex. Bolt (5mmø × 25 mm) Toothed Lock Washer (5mmø) Removal Tool (U-shaped) Antenna Connector Diagram Q'ty 1 2 2 2 1 1 1 2 1 · Remove Mounting Collar q from the main unit temporarily, which are already mounted at shipment. * Caution: Various settings that have been stored in the memory in other on-board equipment (vehicle navigation etc. ) may be lost if the battery terminals are disconnected. [. . . ]