User manual PANASONIC CQ-R595

[. . . ] 1 Mounting Collar (YEFX0216165). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Trim Plate (YEFC05611). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power Connector (YEAJ02877). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Screw Kit (Lock Cancel Plate, Mounting Bolt, Tapping Screw, Hex. [. . . ] Press and hold [4] (RANDOM) for more than 2 seconds. Press and hold [4] (RANDOM) again for more than 2 seconds to cancel. Press and hold [6] (REPEAT) for more than 2 seconds. Press and hold [6] (REPEAT) again for more than 2 seconds to cancel. Display Change Press [DISP] (Display). Track/play time/disc Scan Play The first 10 seconds of each tracks is played in sequence. Direct Disc Selection (Only for remote control of CQ-R595) Example: Disc number 5 q Press [#]. Note: To suspend direct disc selection, press [#] or [DISP]. Random, Scan and Repeat plays are canceled once [#] is pressed. Press [5] (SCAN). *Clock time Press [5] (SCAN) again to cancel. * "ADJUST" is displayed when the clock is not adjusted. (a Page 11 for clock setting) Disc Scan Play From the next disc, the first 10 seconds of the first track of all the discs is played in sequence. Press and hold [5] (SCAN) for more than 2 seconds. Press and hold [5] (SCAN) again for more than 2 seconds to cancel. 20 CQ-C3400/C3300/C3100W CQ-C3400/C3300/C3100W 21 E N G L I S H 15 Setting Turn [VOLUME]. S HDB E N G L I S H 16 CQ-R595 OPEN R PW SOURCE VOLUME PUSH LEVEL TUNE TRACK DISP SEL Press [VOLUME] (SEL: Select). [DISP] (Return to regular mode) Note: Press [DISP] to return to the regular mode. If no operation takes place for more than 7 seconds in audio setting (2 seconds in the volume setting), the display returns to regular mode. DISC / FOLDER DM MUTE SCROLL RANDOM SCAN REPEAT 1 2 3 4 5 6 BAND APM Audio Setting Volume Default: 18 Setting range: 0 to 40 Press [VOLUME] (SEL: Select) to open the menu. q : Up w : Down Bass/Treble You can adjust the bass and treble sound. Default: BAS (bass) 0 dB TRE (treble) 0 dB Setting range: 12 dB to +12 dB (by 2 dB) Press [VOLUME] (SEL: Select). Turn [VOLUME]. Do not use it to attach any other model. IMPORTANT When this unit is installed in dashboard, ensure that there is sufficient air flow around the unit to prevent damage from overheating, do not block any ventilation holes on the unit. E N G L I S H 20 w 1 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. The tabs to be bent vary depending on the car. To securely install the unit, fully bend a number of the tabs so that there is no rattling. Example: Tab e r t 30 or less y Caution: Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. u q Mounting Collar i e Power Connector Dashboard Installation Installation Opening The unit can be installed in 53 mm any dashboard having an opening as shown at right. 182 mm The dashboard should be 4. 5 mm - 6 mm thick in order to be able to support the unit. Installation Precautions This product should be installed by a professional installer, if possible. In case of difficulty, please consult the shop where you purchased the product. This system is to be used only in a 12-volt, DC battery system (car) with negative ground. Follow the electrical connections carefully (a Page 3032). Failure to do so may result in damage to the unit. [. . . ] The number of auto preset stations is less than 6. The number of receivable stations is less than 6. aMove to an area where receivable stations number is maximum, and try presetting. The contact of the battery lead is poor, or the battery lead is not always powered. [. . . ]