User manual PANASONIC CQ-4330U

[. . . ] R Heavy Duty Cassette/Weather Band Receiver with CD Changer Control / XM Radio Ready CQ-4330U APM DISP CLK PWR BAND MODE ALM CQ-4330U LOUD Operating Instructions VOL PUSH MUTE DISC CD SCAN RPT RDM SEL/SAT BASS/TREB BAL/FADER TUNE SEEK SCAN ILL 1 MTL 2 NR 3 TPS 4 REP 5 SKP 6 · Please read these instructions carefully before using this product and keep this manual for future reference. Safety Information WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN, SPLASHING, DRIPPING OR MOISTURE. The following applies only in the U. S. A. Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. CAUTION: PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR INSTALLATION OF THE UNIT. NOTICE: This product contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information please contact your local authorities, or the Electronics Industries Alliance: <http://www. eiae. org. > Find the model number and serial number on either the back or bottom of the unit. Please record them in the space below and retain this booklet as a permanent record of your purchase to help with identification in case of theft. [. . . ] Select the next available compact disc. If failure persists, press the reset switch on the CD changer. If normal operation is not restored yet, call the store where you purchased the unit or the nearest panasonic service center to ask for repairs. No disc in the changer (magazine) Insert discs into the changer (magazine). 15 CQ-4330U XM Control Preparation: Connect the XM receiver (XM DIRECT MODEL:XM-RVR-D-OO1) to the Unit CQ-4330U. XM satellite radio is available on a chargable basis. q XM Mode (When a XM receiver is connected. ) Press [MODE] to change to the XM mode. APM DISP r Channel Scan CLK PWR BAND MODE ALM CQ-4330U LOUD VOL PUSH MUTE DISC CD SCAN RPT RDM SEL/SAT BASS/TREB BAL/FADER TUNE SEEK SCAN ILL 1 MTL 2 NR 3 TPS 4 REP 5 SKP 6 Press [SCAN], each channel in ascending order will be scanned sequentially and the display will blink for 5 seconds. Press [SCAN] again to stop scamming and the last channel will continue to broadcast. w Band Press [BAND]. [CATEGORY] XM displays as follows, (Example) Satellite Radio after 2 seconds Indicator e Channel Selection Press [}]: Up Press [{]: Down Press and hold [}] or [{] for more than 2 seconds to change channels rapidly. XM Band Preset Number Channel Number after 5 seconds Channel Name Category Priority Setting and Selecting · Push the knob [SEL] for more than 2 seconds. (Push and hold) (without operation during 2 seconds. ) (when category is set ON. ) (without operation during 5 seconds. ) category name (interdisplay for 2 seconds. ) turn left (blinks) turn right (when category is set OFF. ) 16 CQ-4330U · When the display shows "CAT ON", Press [2] (}): Up Press [1] ({): Down (without operation during 5 seconds. ) 1 MTL 2 NR 1 MTL 2 NR Category Name Press [2] or [1]. (Receiving) (Received) Category Name (interdisplay for 2 seconds. ) Push and hold the knob [SEL] for more than 2 seconds to resume the normal display. category on indicator Notes: CAT OFF: Every channel can be selected from every category. CAT ON: Only channels in the current category can be selected. Default: CAT OFF Manual Preset Memory Up to 6 channels each can be saved in the XM1, XM2 and XM3 preset station memories. q Select a band and a channel. BAND TUNE SEEK w Press and hold [1] to [6] for more than 2 seconds to memorize. 1 MTL 2 NR 3 TPS 4 REP 5 SKP 6 · The channel number and the preset number blink once. Note: Existing saved channels are overwritten with new channels after the above procedure. Preset memory Calling q Select a band. BAND w Press [1] to [6]. 1 MTL 2 NR 3 TPS 4 REP 5 SKP 6 Note: When category is on category will be off after pressed any preset button [1] to [6]. 17 CQ-4330U XM Control (Continued) Display Change Press and hold [MODE] (DISP) for more than 2 seconds. MODE Channel name (Press and hold) (Reading artist name) Artist name (Reading song title) Song title (Reading category) Category name Note: Display when there is no name/title or can not decode. XM ID Confirmation · Push and hold the knob [SEL] for more than 2 seconds and then push again during 2 seconds. (Push and hold) (Push) Note: If the ID number is 12345678 for example. · Push the knob for more than 2 seconds to resume to the previous mode when displaying "RADIO ID" or ID number. · You can also see ID number by selecting CH0. Error display XM ID is communication fails, Press [MODE] to another mode. 18 CQ-4330U Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. Cautions: · Do not use the unit if it malfunctions or if there is something wrong. · Do not use the unit in irregular condition, for example, without sound, or with smoke or foul smell, which can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. Troubleshooting Tips Common Trouble Cause/Step Vehicle's ignition switch is not on. a Turn your vehicle's ignition switch to ACC or ON. [. . . ] The dashboard should be 3/16" (4. 75 mm) ­ 7/32" (5. 56 mm) thick in order to be able to support the unit. (b) Using the rubber cushion (option) Rubber cushion (option) Rear support bracket (provided on the vehicle) Mounting bolt (5 mmø) q Mounting collar 23 CQ-4330U Installation (Continued) Cautions: · We strongly recommend that you wear gloves for installation work to protect yourself from injuries. · When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. First complete the electrical connections, and then check them for correctness. (a page 26) The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model. 1 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. The tabs to be bent vary depending on the vehicle. [. . . ]