User manual PANASONIC CQ-5200U

[. . . ] High Power CD Player / Receiver with Changer Control High Power CD Player / Receiver CQ-5400U/5200U Operating Instructions Please read these instructions carefully before using this product and save this manual for future use. Panasonic welcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family. Use This Equipment Safely When Driving Keep the volume level low enough to be aware of road and traffic conditions. When Vehicle Washing Do not expose the equipment, including the speakers and CDs, to water or excessive moisture. [. . . ] The display will blink and the first 10 seconds of each track on the disc play in order. Disc Press [SCAN] again to cancel. 12 CD Changer Basics (Only for CQ-5400U) Note: CD changer functions are designed for an optional CD changer unit. Press and hold Starting the CD Changer Once the CD changer has been connected, press [MODE] to change to the CD changer mode. j (Hold [i] or [j] to change numbers rapidly. ) i j d Once the time has been set, release [CLK]. Note: When the clock is not set yet, "SET" is displayed. or Time Reset When you want to reset the time, repeat steps to above. Clock Display Press [CLK] to display the current time. After a few seconds, current time returns on the display. Note: The current time will be displayed at all the time even the power of the radio is turned off. 15 Press and hold Alarm Time Setting Press and hold [ALM] until you have set the alarm time, "AM 12:00" blinks , and the alarm time setting mode is activated. j (Hold [i] or [j] to change numbers rapidly. ) i j d When you have set the alarm time, release [ALM]. Note: When the alarm is not set yet, "AM 12:00" is displayed. or Alarm Time Reset When you want to reset the alarm time, repeat steps above. to Alarm Operation Alarm is switched to ON or OFF each time [ALM] is pressed. When the alarm is switched to ON, the alarm sound will activate at the set alarm time. Turning off the Alarm Sound The alarm sound will turn off automatically after 90 seconds. Otherwise, press [ALM] once. Alarm output Volume Selection You can select ALARM VOL 1 (or VOL 2) by pressing [ALM] in sequence and the display will show as follows. ALARM TIME a ALM VOL 1 ALM VOL 2 a (display 3 seconds) (display 2 seconds) (display 2 seconds) OFF Cautions: Be careful not to set wrong alarm time, otherwise, the alarm may sound while driving. If the alarm is set, be sure to check the set alarm time by pressing and holding [ALM] for more than 2 seconds. If volume is set at "0" step, the output volume will be muted. (Even when ALARM is acting. ) 16 If abnormal Operation appears Reset Switch Use a unflexible thin stick to press this switch in the hole. The initial settings will resume and all electronic memory settings previously registered will be lost. 17 Installation Guide WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers in attempting to install this product. Any attempt to install this product in a motor vehicle by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. Overview This equipment should be installed by a professional. However, if you plan to install this unit yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to "WARNING" statement above). Connect the vehicle wires to the wires of the power connector. If you do encounter problems, please consult your nearest professional installer. Installation Hardware No. [. . . ] Excessive moisture Wait for a while before using the unit. Wiring connection is not properly Confirm all wiring connection done. Volume control is at "minimum" Adjust the volume control to the position. Replace the fuse with the correct rating. Check the speaker cords. Sound distorted due to vibration Inverted sound (Left/Right conn- The speaker cords are inverted. [. . . ]