User manual PANASONIC CQ-5330U

[. . . ] R Heavy Duty CD player/weather Band Receiver with CD changer Control/XM Radio Ready CQ-5330U CLK PWR ALM VOL PUSH SEL / SAT DISP CQ-5330U LOUD Operating Instructions TUNE SEEK MODE DISC CD SCAN RPT RDM MUTE BAND BASS/TREB/BAL/FADER SCAN ILL 1 APM 2 3 4 5 6 · Please read these instructions carefully before using this product and keep this manual for future reference. Safety Information WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN, SPLASHING, DRIPPING OR MOISTURE. The following applies only in the U. S. A. Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. CAUTION: PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR INSTALLATION OF THE UNIT. Laser Products: Wave length: 780 nm Laser power: No hazardous radiation is emitted with safety protection. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE INCLUDED COMPONENTS. NOTICE: This product contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. [. . . ] CAT ON: Only channels in the current category can be selected. Default: CAT OFF Manual Preset Memory Up to 6 channels each can be saved in the XM1, XM2 and XM3 preset station memories. q Select a band and a channel. BAND TUNE SEEK w Press and hold [1] to [6] for more than 2 seconds to memorize. 1 2 3 4 5 6 · The channel number and the preset number blink once. Note: Existing saved channels are overwritten with new channels after the above procedure. Preset memory Calling q Select a band. BAND w Press [1] to [6]. 1 2 3 4 5 6 Note: When category is on category will be off after pressed any preset button [1] to [6]. 17 CQ-5330U XM Control (Continued) Display Change Press and hold [MODE] (DISP) for more than 2 seconds. MODE Channel name (Press and hold) (Reading artist name) Artist name (Reading song title) song title (Reading categry) Category name Note: Display when there is no name/title or can not decode. XM ID Confirmation · Push and hold the knob [SEL] for more than 2 seconds and then push again during 2 seconds. (Push and hold) (Push) Note: If the ID number is 12345678 for example. · Push the knob for more than 2 seconds to resume to the previous mode when displaying "RADIO ID" or ID number. · You can also see ID number by selecting CH0. Error display XM ID is or communication fails, Press [MODE] to another mode. 18 CQ-5330U Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. Cautions: · Do not use the unit if it malfunctions or if there is something wrong. · Do not use the unit in irregular condition, for example, without sound, or with smoke or foul smell, which can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. Troubleshooting Tips Common Trouble Cause/Step Vehicle's ignition switch is not on. a Turn your vehicle's ignition switch to ACC or ON. Powere connector is not correctly connected. a Connect the power connector to the terminal that is always active. Power connector is not correctly connected. a Connect the power connector to your vehicle's ACC source. Grounding wire is not correctly connected. a Connect the grounding wire to a metal part of the venicle. a Connect cables correctly. Noise. The ground lead is not connected properly. a Connect the ground lead properly. 19 CQ-5330U Troubleshooting (Continued) Radio Trouble Cause/Step Station is too far, or signals are too weak. a Select other stations of higher signal level. The radio antenna is not extended enough. [. . . ] Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals. After completing installation of the main unit, set the equipment again according to the record. · Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. o (a) Using the rear support strap t Dashboard Installation Installation Opening This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 3/16" (4. 75 mm) ­ 7/32" (5. 56 mm) thick in order to be able to support the unit. (b) Using the rubber cushion (option) Rubber cushion (option) Rear support bracket (provided on the vehicle) Mounting bolt (5 mmø) q Mounting collar 26 CQ-5330U Cautions: · We strongly recommend that you wear gloves for installation work to protect yourself from injuries. [. . . ]