User manual PANASONIC CQ-C1300W

[. . . ] E N G L I S H 1 Panasonic welcomes you to their constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family. Remote Control Battery Installation "+"-face up E N G L I S H 2 Precautions When Driving Keep the volume level low enough to be aware of road and traffic conditions. Battery Notes Battery life: approx. 6 months Battery handling: no disassembling (prevention of burst) no short-circuiting (prevention of burst) avoidance of fire (prevention of burst) out of the reach of children (prevention of swallow) Replaced old battery: Follow the local regulations. Disc Mechanism Do not insert coins or any small objects. [. . . ] (a Page 28-29) The included Mounting Collar q is designed specially for this unit. Do not use it to attach any other model. IMPORTANT When this unit is installed in dashboard, ensure that there is sufficient air flow around the unit to prevent damage from overheating, do not block any ventilation holes on the unit. E N G L I S H 16 w 1 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. The tabs to be bent vary depending on the car. To securely install the unit, fully bend a number of the tabs so that there is no rattling. Example: Tab e r t 30 or less y Caution: Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. u q Mounting Collar i e Power Connector Dashboard Installation Installation Opening The unit can be installed in 53 mm any dashboard having an opening as shown at right. 182 mm The dashboard should be 4. 5 mm - 6 mm thick in order to be able to support the unit. Installation Precautions This product should be installed by a professional installer, if possible. In case of difficulty, please consult the shop where you purchased the product. This system is to be used only in a 12-volt, DC battery system (car) with negative ground. Follow the electrical connections carefully (a Page 2829). Failure to do so may result in damage to the unit. Connect the power lead (red) after all other connections are made. Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal. Insulate all exposed wires to prevent short circuiting. Secure all loose wires after installing the unit. Please carefully read the operating and installation instructions of the respective equipment before connecting it to this unit. Methods for Fixing the Rear of the Unit. (a) Using the Rear Support Strap y. u Tapping Screw Fire Wall of Car 3 mm Mounting Holes w Mounting Bolt i Hex. Nut y Rear Support Strap w Mounting Bolt q Mounting Collar Mounting Springs (C) (b) Using the Rubber Cushion (Option) Rear Support Bracket (Provided on the car) Rubber Cushion (Option) Engage the Mounting Springs (C) in the mounting holes of the Mounting Collar q firmly. Mounting Spring 2 3 4 Mounting Hole Establish the rear of the unit. After fixing Mounting Bolt w and Power Connector e, fix the rear of the unit to the car body by either method (a) or (b) shown on the previous page. Insert Trim Plate r. After installation reconnect the negative () battery terminal. w Mounting Bolt q Mounting Collar 24 CQ-C1300W CQ-C1300W 25 E N G L I S H 17 Installation (continued) To Remove the Unit q (a) Switch off the power of the unit. (b) Press the release button [ ]. Anti-Theft System This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable. Removable Face Plate Case E N G L I S H 18 q Pull out Place Removable Face Plate into Case q Switch off the power of the unit. (a Previous page) e Gently press the bottom of the case and open the cover. Place the face plate into the case and take it with you when you leave the car. w (c) Pull out the face plate on the right side of the unit. w Remove the trim plate r with a screwdriver. Screwdriver Install Removable Face Plate 1 w r Trim Plate 2 q Slide the left side of the removable face plate in place. [. . . ] aRemove the foreign material, or use a flawless disc. There is a flaw or foreign material on the disc. aRemove the foreign material, or use a flawless disc. aSecure the unit to the console box with the rear support strap, etc. [. . . ]