User manual PANASONIC CQ-DF202U

[. . . ] E N G L I S H 1 Power and Sound Controls Power Turn the key in the ignition until the accessory indicator lights. Power off: Press [SOURCE] (PWR) again and hold. Note: When the power is switched on for the first time, a demonstration message appears on the display. To cancel this display, press [DISP] (display). ACC ON Clock Basics Audio Mode (Bass/Treble/Balance/Fader) 1 Press [SEL] to select the audio mode. Regular mode Volume Fader Bass Treble Balance The 12-hour system is used for the clock. E N G L I S H 2 Initial Time 1 Press [DISP] (CLOCK). (Clock display. ) [% TUNE], [$ TUNE] (Hours, minutes) SCAN/APM REMOTE [DISP] (CLOCK) 45WX4 OPEN CQ-DF202U 45WX4 OPEN SCAN/APM REMOTE CQ-DF202U RANDOM RANDOM VOL SEL BAND TUNE TRACK LOUD CD RECEIVER REP PWR VOL SEL BAND TUNE TRACK LOUD CD RECEIVER REP PWR SOURCE SOURCE C MONO/LO MUTE 7 1 8 2 9 3 10 4 11 5 12 6 CLOCK DISP LEVL C MONO/LO MUTE 7 1 8 2 9 3 10 4 11 5 12 6 CLOCK DISP LEVL Volume [" VOL]: Up [# VOL]: Down Press and hold for rapid adjustment. Level Meter (Only for main unit) When the power is on, the level of sound sources, such as radio and CD, is displayed. [. . . ] CQ-DF202U Replace the Fuse Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or connecting the product directly without a fuse, could cause fire or damage to the stereo unit. If the replacement fuse fails, contact your nearest Panasonic Servicenter for service. 20 CQ-DF202U 21 E N G L I S H 13 Installation Guide Identify All Leads WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. Speakers Identify the car speaker leads. There are two leads for each speaker which are usually color coded. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. When you label them, include the speaker location for each. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 14 Installation Hardware No. 1 2 3 4 5 6 7 8 Item Mounting collar Hex. [. . . ] Press and hold [SEL] to turn the security indicator on or off. ("LED ON" or "LED OFF") Default Display Security indicator Blinks Lock lever OFF Security indicator 4 Remove the unit pulling with both hands. Caution: This face plate is not waterproof. Do not expose it to water or excessive moisture. Do not remove the face plate while driving your car. [. . . ]