User manual PANASONIC CQ-DF302W

[. . . ] Removable Full Front CD player/ Receiver with CD Changer Control SCAN AUTO·P REMOTE CQ-DF302W 45WX4 OPEN CQ-DF302W Operating Instructions RANDOM VOL SEL BAND TUNE TRACK LOUD CD RECEIVER WITH CHANGER CONTROL REP PWR SOURCE MONO/LOC MUTE 7 1 8 2 9 3 10 4 11 5 12 6 CLOCK DISP LEVL DIMMER Please read these instructions carefully before using this product and save this manual for future use. E N G L I S H Panasonic welcomes you to our ever growing family of electronic product owners. We know that this product will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical engineering, manufactured with carefully selected components and assembled by people who take pride in their work. Once you discover the quality, reliability, and value we have built into this product, you too will be proud to be a member of our family. Use this Product Safely When Driving Keep the volume level low enough to be aware of road and traffic conditions. Disc Mechanism Do not insert coins or any small objects. [. . . ] Turn on the ignition to check the unit for proper operation. If you have difficulties, consult your nearest authorized professional installer for assistance. E N G L I S H 12 Preparation We strongly recommend that you wear gloves for installation work to protect yourself from injuries. When bending the mounting tabs of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. Disconnect the cable from the negative - battery terminal (see caution below). Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30o. Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If the bulb also turns off and on, that outlet is the car power lead. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN). Battery Lead If your stereo unit has a yellow lead, you will need to locate the car's battery lead. Otherwise you may ignore this procedure. (The yellow battery lead provides continuous power to maintain a clock, memory storage, or other function. ) If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. Connect All Leads Now that you have identified all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram ( pages 25, 26) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Use electrical tape to cover all exposed wires. Important: Connect the red power lead last, after you have made and insulated all other connections. Ground Connect the black ground lead of the power connector to the metal car chassis. Less than 30x Caution: Do not disconnect the battery terminals of a car with a trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. Dashboard Installation Installation Opening 53 mm 182 mm This unit can be installed in any dashboard having an opening as shown above. The dashboard should be 4. 75 mmj5. 56 mm thick in order to be able to support the unit. Final Installation Lead Connections Connect all wires, making sure that each connection is insulated and secure. Bundle all loose wires and fasten them with tape so they will not fall down later. Now insert the stereo unit into the mounting collar. [. . . ] Insert discs into the changer (magazine). Left and right sounds are reversed in stereo listening. Notes: There may be cases where the disc numbers affected by an error are displayed before "E1" or "E2". Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the operating instructions for the changer used. CQ-DF302W 28 CQ-DF302W 29 E N G L I S H 21 Maintenance Care of the Unit Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. [. . . ]