User manual PANASONIC CQ-DPX85EU

[. . . ] 12111 Riverside Way Richmond, BC V6W 1K8 Tel: (604) 278-4211 Fax: (604) 278-5627 Toronto Panasonic Canada Inc. 5770 Ambler Drive Mississauga, ON L4W 2T3 Tel: (905) 624-8447 Fax: (905) 238-2418 Customer Services Directory Service in Puerto Rico Panasonic Puerto Rico, Inc. Panasonic Sales Company Factory Servicenter: Ave. 9. 5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985 Phone (787) 750-4300, Fax (787) 768-2910 IF YOU SHIP THE PRODUCT TO A SERVICENTRE Carefully pack and send prepaid, adequately insured and preferably in the original carton. [. . . ] Some cars equipped with the electrical safety system have specific procedures of battery terminal disconnection. FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL INJURY OR DEATH. Use the proper power supply. This product is designed for operation with a negative grounded 12 V DC battery system. Never operate this product with other battery systems, especially a 24 V DC battery system. Never use safety-related components for installation, grounding, and other such functions. Do not use safety-related vehicle components (fuel tank, brake, suspension, steering wheel, pedals, airbag, etc. ) for wiring or fixing the product or its accessories. Protect the Deck Mechanism. Do not insert any foreign objects into the slot of this unit. Do not disassemble or modify the unit. Do not disassemble, modify the unit or attempt to repair the product yourself. If the product needs to be repaired, consult your dealer or an authorized Panasonic Servicenter. Installing the product on the air bag cover or in a location where it interferes with airbag operation is prohibited. Check for piping, gasoline tank, electric wiring, and other items before installing the product. If you need to open a hole in the vehicle chassis to attach or wire the product, first check where the wire harness, gasoline tank, and electric wiring are located. Then open the hole from outside if possible. Do not use the unit when it is out of order. If the unit is out of order (no power, no sound) or in an abnormal state (has foreign matter in it, is exposed to water, is smoking, or smells), turn it off immediately and consult your dealer. Refer fuse replacement to qualified service personnel. When the fuse burns out, eliminate the cause and have it replaced with the fuse prescribed for this unit by a qualified service engineer. Make sure that wiring is completed before installation. To prevent damage to the unit, do not connect the power connector until the whole wiring is completed. Do not connect more than one speaker to one set of speaker leads. (except for connecting to a tweeter) Observe the following cautions when installing. Refer wiring and installation to qualified service personnel. Installation of this unit requires special skills and experience. For maximum safety, have it installed by your dealer. [DISP] (Display) exits from the audio menu. 1 Display the audio menu. Press [VOL] (PUSH SEL: Select). Note: If no operation takes place for more than 5 seconds in the audio menu (2 seconds in Main volume adjustment), the display returns to the regular mode. 2 Select a mode to be adjusted. Press [VOL] (PUSH SEL: Select). 3 Adjust. Turn [VOL]. Volume (Setting Range: 0 to 40, Default: 18) : Up : Down Audio menu Bass (Setting Range: ­12 dB to +12 dB by 2 dB, Default: 0 dB) : Increased : Decreased Treble (Setting Range: ­12 dB to +12 dB by 2 dB, Default: 0 dB) : Increased : Decreased Balance (Setting Range: 15 levels each and 0 (center), Default 0) : Right enhanced : Left enhanced Fader (Setting Range: 15 levels each and 0 (center), Default 0) Note: If the fader is set to front, the pre-amp. : Front enhanced : Rear enhanced Radio (AM/FM ) [BAND] selects a band in the radio source. (APM) (Auto Preset Memory) executes APM in the radio source. (Hold down it for more than 2 seconds) [D·M] (Direct Memory) tunes into the station memorized in D·M. (Hold down it for more than 2 seconds to memorize the current station. ) [SRC] (Source) selects a source. [DISP] (Display) switches the information on the display. Preset buttons [1] to [6] selects a preset station in the radio source, and presets the current station. (Hold down it for more than 2 seconds) [TUNE ]] [TUNE [] down/up the frequency. (Hold down it for more than 0. 5 seconds for seek tuning. ) 1 Press [SRC] (Source) to select the radio source. 3 Select a station. Frequency adjustment [TUNE]]: Lower [TUNE[]: Higher 2 Press [BAND] to select a band. Operation Flow Note: Hold down either of them for more than 0. 5 seconds and release it for station search. Preset station selection Press the corresponding preset button from [1] to [6] to tune into a preset station. lights while receiving an FM stereo signal. Frequency Band Preset Number Display change Press [DISP] (Display) to change the display. Radio Mode Display Radio mode display (Default) Clock display lights while receiving the D·M (Direct Memory) station. Up to 6 stations can be preset in AM, FM1, FM2, and FM3 respectively. Preset stations can be simply called up by pressing one of the preset buttons from [1] to [6]. Manual station preset 1 Tune into a station. 2 Hold down one of the preset buttons from [1] to [6] for more than 2 seconds. Station Preset Auto Preset Memory (APM) With this operation, stations with good receiving conditions can be automatically stored in the preset memory. 1 Select a band. 2 Hold down [BAND] (APM) for more than 2 seconds. The preset stations under best receiving conditions are received for 5 seconds each after presetting the stations (SCAN). [. . . ] If the described suggestions do not solve the problem, it is recommended to take the unit to your nearest authorized Panasonic Servicenter. The product should be serviced only by qualified personnel. Please refer checking and repair to professionals. Panasonic shall not be liable for any accidents arising out of neglect of checking the unit or your own repair after your checking. [. . . ]