User manual PANASONIC CQ-FRX920

[. . . ] 6-25 CHINESE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-45 RUSSIAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46-65 Panasonic welcomes you to their constantly growing family of electronic products owners. We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and assembled by people who are proud of the reputation their work has built for our company. [. . . ] Select the next available compact disc. c DISC No. Appears on the display when compact disc is scratched. Select the next available compact disc. Fast forward/Fast reverse Press and hold [f TRACK] : Fast forward [a TRACK] : Fast reverse Release to resume the regular CD Changer play. Appears on the display when the unit stops operating for some reason. Press the reset switch on the CD Changer (option). CDC 0000 Appears on the display when there is no disc in the magazine. 14 CQ-FRX920 CQ-FRX920 15 E N G L I S H 11 Installation Preparation ¡Before installation, check the radio operation with antenna and speakers. ¡Disconnect the cable from the negative (­) battery terminal (see caution below). ¡Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. Supplied Hardware No. q w e r t y u Item Mounting Collar Mounting Bolt (5 mmø) Tapping Screw (5 mmø x 16 mm) Rear Support Strap Hex. Nut (5 mmø) Power Connector Trim Plate Diagram Q'ty 1 1 1 1 1 1 1 Cautions: ¡We strongly recommend that you wear gloves for installation work to protect yourself from injuries. ¡When bending the mounting tab of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. First complete the electrical connections, and then check them for correctness. (a Page 20) The included Mounting Collar q is designed specially for this unit . Do not use it to attach any other models. E N G L I S H 12 1 1 Insert Mounting Collar q into the dashboard, and bend the mounting tabs out with a screwdriver. 30° or less Caution: Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. Lock Lever (C) Power Connector y Dashboard Installation 53 mm Installation Opening The unit can be installed in 182 mm any dashboard having an opening as shown at right. e Move the face plate up and down a few times to make sure it is secure. Then close the front panel and press down the right side of the face plate until it clicks into place. Screwdriver Security Indicator The security indicator blinks when the removable face plate is removed from the unit. Press and hold [SEL] for more than 2seconds when the power is on. "LED On" is displayed, and the security indicator turns on. (Default: LED On) Security Indicator r Remove the unit pulling with both hands. Display Cautions: ¡Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. ¡If dirt or other foreign substances get on the contacts, wipe them off with clean and dry cloth. ¡Do not apply a strong downward force onto the face plate and do not put anything on it while it is open, or it might be damaged. Security Indicator Blinks OFF Caution: When you want to remove the unit, the security indicator functions can be canceled by following procedure. ¡Install the removable face plate. ¡Disconnect the power connector for more than 3 minutes and then reconnect it. 18 CQ-FRX920 CQ-FRX920 19 E N G L I S H 15 Electrical Connections Cable Wiring Diagram Example : Connection with CD Changer CX-DP88N (Option). Changer Control DIN Cord CD Changer (L) (White) CH·C-IN CX-DP88N (option) RCA Cord Antenna (R) (Red) CD Changer Control Connector Preamp out Connector (Pre-out) Front Preamp out Connector (Pre-out) Rear Cassette Receiver CQ-FRX920 Ground Lead To a clean, bare metallic part of the car chassis Extension Cord (DIN/BATT/RCA/GND) (Supplied for an optional CD Changer) (Black) Cautions: ¡This unit is designed for use in a car having a 12-volt negative ground battery system. ¡To prevent damage to the unit, be sure to follow the connection diagram below. ¡Strip about 5 mm of the lead ends for connection. [. . . ] Using different substitutes or fuses with higher ratings, or connecting the unit directly without a fuse, could cause fire or damage to the unit. If the fuse replacement fails, contact your shop when you purchased this unit. Unit does not turn on. Accessory cable is not correctly connected. Grounding wire is not correctly connected. Mute is set to ON. No sound Cables are not correctly connected. [. . . ]