User manual PANASONIC CQ-H07E

[. . . ] 2 Press SET /[SET]. 3 Set Press or /[#] or ["]. 7 8 9 [MENU] [#] ["] (set) [%] [$] (submenu) [SET] # NUMBER 0 MUTE Car Audio 7 color (below) Changes according to the volume level. Red Note: Press EXIT /[MENU]/[DISP] (display) to return to the regular mode. Press RTN /[RET] (RETURN) to return to the previous display. Color Change You can change the color of the display. Default: 7COLOR Variety: 7COLOR, LEVEL, RED, PURPLE, BLUE, AQUABLUE, GREEN, YELLOW, WHITE Purple Select Select Blue Aqua blue Green Yellow White Direct Operation In the case of remote control, as an alternative to performing operations from the menu, the operations can be performed directly using the buttons shown below. SOURCE PWR BAND RETURN RET MENU [FACE] FACE S ·A S·A DIMMER DISP DIM ET S 1 2 3 4 RANDOM 5 SCAN 6 REPEAT VOL 7 8 9 # NUMBER 0 MUTE Car Audio 40 CQ-HX1083/1003W CQ-HX1083/1003W 41 E N G L I S H 23 Audio Settings [AUDIO] 3 SET 1 [MENU] 2 SET RTN EXIT [RET] (RETURN) SOURCE PWR BAND RETURN RET MENU E N G L I S H 24 FACE S ·A S·A DIMMER 1 2 3 Lights during menu play setting. [. . . ] For details, refer to the user manual of your writing software. You ran the file in fast forward or fast reverse during playback or turned off the ignition switch of the car during playback. Playing another file will return the file playing time to normal. You played a VBR (Variable Bit Rate) format file. When there is no MP3/WMA files in the specified folder during direct MP3/WMA folder selection. Select another folder which contains MP3/WMA files. The player cannot read the file you are trying to play for some reason. (File recorded in an unsupported file system, compression scheme, data format, file name extension, damaged data, etc. ) Select a file that the player can read. Confirm the type of data recorded on the disc. An attempt has been made to play a copy-protected WMA file. Play WMA files which are not copy-protected. 52 CQ-HX1083/1003W CQ-HX1083/1003W 53 E N G L I S H 35 Troubleshooting (Continued) If the Unit does not Operate Properly Reset switch Push a thin, unbreakable object into this hole to press the reset switch. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. Dashboard Specifications Thickness Min. 5. 56 mm 53 mm 182 mm Identify All Leads The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. This will help avoid confusion when making connections later. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Identify the leads in the following order. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. Installation Hardware No. 1 2 3 4 5 6 7 8 9 : ; Item Mounting collar Hex. nut (5 mm·) Rear support strap Tapping screw (5 mm·a16 mm) Mounting bolt (5 mm·) Power connector Trim plate Mounting spring (R) Mounting spring (L) L Diagram Q'ty 1 1 1 1 1 1 1 1 1 2 2 The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above. ) Identify and label the car wires. [. . . ] ; Lock cancel plate Insert the tab end in the outer groove. Security Indicator The security indicator blinks when the removable face plate is removed from the unit. The function is activated when the security function is on. (page 46) Security indicator 1 Panel Removal Alarm This alarm sounds to warn you not to forget to remove the panel before leaving your car. The function is activated when the security function is on. [. . . ]