User manual PANASONIC CQ-MR707

[. . . ] Press [LEVL] (level) to change the level meter display. 2 Press [" VOL] or [# VOL] to change each level. Bass: Adjustable range: j12 dB to i12 dB (by 3 dB step) Hours 2 Press and hold [DISP] (CLOCK) for more than 2 seconds. (Hours blink. ) (Default) Volume level (0 to 40) 3 Press [% TUNE] or [$ TUNE]. (Hours set. ) Minutes 4 Press [DISP] (CLOCK). (Minutes blink. ) Pattern 1 Pattern off Pattern 2 Pattern 3 Pattern 4 Treble: Loudness (Only for main unit) Press [LOUD] to enhance bass and treble tones at low or medium volume. MONO Display Change Press [DISP] (CLOCK) to switch to the clock display. When the power is off: No display Clock display Balance: Adjustable range: j12 dB to i12 dB (by 3 dB step) R (right speaker) or L (left speaker) 5 Press [% TUNE] or [$ TUNE]. (Minutes set. ) LOUD Press [LOUD] again to cancel. Adjustable range: 1 to 15 (by 1 dB step) Balance center 6 Press [DISP] (CLOCK). (End. ) Note: Press and hold [% TUNE] or [$ TUNE] for more than 2 seconds to change numbers rapidly. Fader: Mute Press [MUTE] to mute the sound completely. F (front speaker) or R (rear speaker) MUTE Press [MUTE] again to cancel. Anti-volume-blast circuit: When the power is switched off and on again, the volume slowly rises to the previous level. [. . . ] Press [OPEN] to open the panel and press [<] (eject). If normal operation is not restored, call the store where you purchased the unit or the nearest Servicenter to ask for repairs. Do not leave discs on the following places: Direct sunlight Near car heaters Dirty, dusty and damp areas Seats and dashboards Disc cleaning Use a dry, soft cloth to wipe from the center outward. Caution on new discs A new disc may have rough edges on its inner and outer perimeter. Remove the rough edges using a pencil, etc. Do not attach any seals or labels to your discs. Do not use irregular shaped discs. <Right> <Wrong> Rough edges Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. Use a dry, a soft cloth for routine exterior cleaning. Never use benzine, thinner or other solvents. Do not write on the disc label in a heavy pen or ballpoint pen stroke. Product Servicing If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest authorized Panasonic Servicenter. The product should be serviced only by a qualified technician. Notes on CD-Rs/RWs You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), either due to their recording characteristics or dirt, fingerprints, scratches, etc. CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them inside a car for extended periods may damage them and make playback impossible. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 14 Installation Hardware No. 1 2 3 4 5 6 7 8 Item Mounting collar Hex. nut (5 mm·) Rear support strap Tapping screw (5 mm·a16 mm) Mounting bolt (5 mm·) Power connector Removable face plate case Trim plate Diagram Q'ty 1 1 1 1 1 1 1 1 If you encounter problems, please consult your nearest professional installer. Caution: This unit operates with a 12 V DC negative ground auto battery system only. Do not attempt to use it in any other system. Before you begin installation, look for the items which are packed with your unit. Warranty Card. . . Fill this out promptly. Panasonic Servicenter List for Service Directory . . . Keep for future reference in case the product needs servicing. Installation Hardware. . . Needed for in-dash installation. Turn the ignition on to the accessory position, and ground one lead of the test bulb to the chassis. [. . . ] 2 Fit the other hold on the other pin applying slight pressure. 3 Move the face plate up and down a few times to make sure it is secure. Then close the front panel and press down the right side of the face plate until it clicks into plate. Contact 1 3 2 unit while pushing 3 Pull out the screwdriver. down the lock lever with a Lock lever Security Indicator The security indicator blinks when the removable face plate is removed from the unit. [. . . ]