User manual PANASONIC CQ-MR707N

[. . . ] MD Player/Receiver with CD Changer Control AUTO·P CQ-MR707N BAND TRACK TUNE MOS FET 95Wx4 MD RECEIVER WITH CHANGER CONTROL EON EPTY E CT OPEN TA REG VOL SEL CQ-MR707N Operating Instructions REMOTE DISC/PT DISC super bright display with Level Meters RANDOM SCAN AF REPEAT SOURCE POWER MONO/LOC HDB 1 2 3 R 4 5 SCAN REP 6 PTY Bedienungsanleitung Manuel d'instructions Gebruiksaanwijzing Bruksanvisning Manuale di istruzioni Manual de Instrucciones ¡Please read these instructions carefully before using this product and save this manual for future use. ¡Bitte lesen Sie diese Bedienungsanleitung vor der Verwendung dieses Produktes aufmerksam durch und bewahren Sie sie danach für spätere Nachschlagzwecke sorgfältig auf. ¡Prière de lire ces instructions attentivement avant d'utiliser le produit et garder ce manuel pour l'utilisation ultérieure. ¡Leest u deze instructie alstublieft zorgvuldig door voor u dit product in gebruik neemt en bewaar deze handleiding voor later gebruik. [. . . ] Do not attempt to disassemble or adjust any parts. For repair, please consult your nearest authorized Panasonic Service Center. Note: The preset memory is cleared to return to the original factory setting when the power connector or battery is disconnected. Laser Products Caution: This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Laser products: Wave Length 790 nm Laser Power No hazardous radiation is emitted with safety protection. Do not take apart this unit or attempt to make any changes yourself. This unit is a very intricate device that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disassemble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages. 6 CQ-MR707N Remote Control Unit Preparation Battery Installation q Remove the battery holder. Take hold of the holder at position B and pull it out by pushing position A in the direction shown by the arrow. w Install the battery on the battery holder. Set a new battery properly with its (+) side facing up as shown in the figure. Push in the battery holder back into its original position. (Back side) Lithium battery E N G L I S H 2 Position B Battery Notes Remove and dispose of an old battery immediately. Battery Information: ¡Battery Type:Panasonic lithium battery (CR2025) (Included) ¡Battery Life: Approximately 6 months under normal use (at room temperature) Position A Battery holder Caution: Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire. ¡Do not disassemble or short the battery. ¡Keep batteries away from children to avoid the risk of accidents. ¡Be careful to the disposal rules when you dispose of batteries. Main Controls (ATT) Power Button Mode (Source) Button PWR MUTE Mute Button MODE VOL Volume Control Buttons Band, Disc up Button PRG BAND/DISC UP TUNE TRACK Tune, Track Search, Track Selection Buttons Car Audio CQ-MR707N 7 E N G L I S H 3 Power and Sound Controls Power Turn the key in the ignition until the accessory indicator lights. Power off : Press [SOURCE] (POWER) again and hold. Remote control sensor for remote control. Note: When the power is switched on for the first time, a demonstration message appears on the display. To cancel this display, press [ ] (DISP/CT). Volume [}VOL] : Up [{VOL] : Down Press and hold for rapid adjustment. Anti-Volume-Blast Circuit When the power is switched off and on again, the volume slowly rises to the previous level. The anti-volume-blast circuit will not work when the volume level is set lower than position 20 on the display. Volume Level (0 to 40) AUTO·P CQ-MR707N BAND K U E TRACK TUN MOS FET 45Wx4 MD RECEIVER WITH CHANGER CONTROL EON EPTY E CT OPEN TA REG VOL SEL REMOTE DISC/PT DISC super bright display with Level Meters RANDOM SCAN AF REPEAT SOURCE POWER MONO/LOC HDB 1 2 3 R 4 5 SCAN REP 6 PTY Display Control Mode Press [SEL] to change to display q controland hold("PATTERN" appears the the dismode. [. . . ] ¡To prevent damage to the unit, be sure to follow the connection diagram below. ¡Strip about 5 mm of the lead ends for connection (only nonISO connector cords). ¡Do not insert the power connector into the unit until the wiring is completed. ¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. [. . . ]