User manual PANASONIC CQ-VD6503N

[. . . ] Connect the power lead after all other connections are made. Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal. Insulate all exposed wires to prevent short circuiting. Caution ¡Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. [. . . ] y Round Head Screw (5 mmø x 8 mm) Note: Recycle the Round Head Screws that fixed the transportation brackets for two more positions. (a page 5) u Flat-Head Screw (5 mmø x 8 mm) e Pull the unit out with both hands. CQ-VD6503N English 6 7 Installation Guide English Caution 7 (continued) Connecting the Side Brake (Parking Brake) Connection Lead ¡For safety, be sure to ask your nearest professional installer to do this connection. Hand brake Foot brake Side brake (parking brake) switch The side brake (parking brake) switch position varies with car model. For details on the exact location of the side brake (parking brake) switch in your car, contact your dealer. Brake light Battery SIDE BRAKE + -- Side Brake (Parking Brake) Connection Lead (Bright green) When the side brake (parking brake) lever is engaged, the unit is grounded by the chassis. !0 Clip Connector Car chassis q Attach a Clip Connector !0 to the end of the side brake (parking brake) connection lead. Comes up to this point. w The Clip Connector !0 is connected to the power source side lead of the side brake (parking brake) lever. Side Brake (Parking Brake) Connection Lead (Bright green) Power source side lead 8 CQ-VD6503N Electrical Connections Caution ¡Check the connectors provided on your car (see precaution below) before connecting the system. ¡This unit is designed for use in a car having a 12 V negative ground battery system. ¡To prevent damage to the unit, be sure to follow the connection diagram. ¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords). ¡Do not insert the power connector into the unit until the wiring is completed. ¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and prevent cable terminals from touching any metal parts. ¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may clear the memory. ¡Run the cords avoiding the spots where the temperature can be extremely high. Precautions (ISO Connector) ¡The pin arrangement of the power connector conforms to ISO standard. ¡The pin arrangement of ISO connectors in some cars may differ from the ISO standard. ¡Please check that the pin arrangement of the connector in your car conforms to ISO standard. ¡For car types A and B, change the wiring of the red and yellow leads as shown at below. ¡After connection, insulate the portions marked (C) with insulating tape. Note: ¡For cars other than types A and B, please consult your local car shop. ISO Standard ISO A7: IGN or ACC 12 V supply (Red) C (Red) A7 (Yellow) C (Yellow) A4 A4: 12 V Batteries (Continuous supply) ACC BATTERY 15A A Car Type A (Red) A7: 12 V Batteries (Continuous supply) C (Yellow) BATTERY 15A ACC (Yellow) C (Red) A4: IGN or ACC 12 V supply B Car Type B (Red) A7: 12 V Batteries (Continuous supply) C (Red) ACC BATTERY 15A (Yellow) C (Yellow) A4: No connection Note: ¡To prevent from damage to the unit, be sure to follow the wiring diagrams at right. [. . . ] A5 : Motor Antenna Relay Control Lead (Blue/white stripe) To Motor Antenna (Max. Head unit/Expansion Module Connecting cable (Supplied with CY-EM100N) (Video) (Yellow) (L) (White) (R) (Red) VIDEO OUT AUDIO OUT (R) (Red) (L) (White) (Video) (Yellow) 8 mmMA X System-up Connector Camcorder (option) FUSE 1 5 A Expansion Module CY-EM100N (option) DVD Changer >PBT< J A M- S A a CX-DH801N (option) CQ-VD6503N (Rear) (Video) (Yellow) VIDEO OUT RCA cord (option) iPod (Video) (Yellow) (L) (White) CHANGER IN VIDEO-CNT (R) (Red) Conversion Cable for DVD/CD Changer (CA-CC30N, option) Direct Cable for iPod (CA-DC300N, option) CQ-VD6503N English 14 15 Electrical Connections English 15 (continued) Connection with Rear Monitor Note: ¡Refer to the operating instructions for the connected devices, in addition. ¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in order to establish a proper connection. STAND BY (R) ON (G) COLOR LCD MONITOR Caution Rear Monitor ¡For people sitting in the front seats, please enjoy only audio during driving. Panasonic VM1500 Example: Audio Right Audio Left Video Input 8 mmMA X (R) (Red) (Video) (Yellow) FUSE 1 5 A >PBT< J A M- S A a CQ-VD6503N (Rear) (L) (White) (Video) (Yellow) AV-OUT RCA Cord (option) (R) (Red) (L) (White) 16 CQ-VD6503N Connection with Rear View Camera Note: ¡Refer to the operating instructions for the connected devices, in addition. CQ-VD6503N (Rear) Rear View Camera Control Unit (option) 8 mmMA X Camera Input FUSE 1 5 A >PBT< J A M- S A a (Video) (Yellow) Rear View Camera (option) Panasonic i Power Connector REVERSE (Video) (Yellow) RCA Cord (option) Reverse Lead (Violet/white stripe) Camera Input Terminal (Yellow) Connecting the Reverse Lead If using an optional rear view camera, the reverse lead must be connected. [. . . ]