User manual PANASONIC CQ-VD7003N

[. . . ] Connect the power lead after all other connections are made. Be sure to connect the battery lead (yellow) to the positive terminal (+) of the battery or fuse block (BAT) terminal. 0 ­ 30° Caution ¡Do not disconnect the battery terminals of a car with trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. 5. [. . . ] The bracket shape and mounting method vary with car manufacturers, car types and manufacturing year. Please consult your nearest dealer or installer. Select mounting screws according to the hole positions and hole shape of the bracket. t Round Head Screw (5 mmø x 6 mm) 2 pieces Recycle the Round Head Screws that fixed the transportation brackets for two more positions. u Round Head Screw (4 mmø x 3 mm) 4 pieces When using these mounting holes y Flat-Head Screw (5 mmø x 6 mm) 4 pieces t Round Head Screw (5 mmø x 6 mm) i Spacer Use the supplied Spacer i if mounting hole of your car is shaped like below. Mounting Hole of a Bracket (in section) Bracket Existing Bracket (R) o Double-Faced Adhesive Tape t Round Head Screw (5 mmø x 6 mm) i Spacer o Double-Faced Adhesive Tape Existing Bracket (L) (Bracket originally attached to the car) To Remove the Unit q Push the right and left clamp plates outward, one at a time, and pull the unit toward yourself. w After removing the right and left clamp plates, pull the unit with both hands till it comes out. q w Push here to remove the clamp plates. 8 CQ-VD7003N Connecting the Side Brake (Parking Brake) Connection Lead Caution ¡For safety, be sure to ask your nearest professional installer to do this connection. Hand brake Foot brake Side brake (parking brake) switch The side brake (parking brake) switch position varies with car model. For details on the exact location of the side brake (parking brake) switch in your car, contact your dealer. Brake light Battery SIDE BRAKE + -- Side Brake (Parking Brake) Connection Lead (Bright green) When the side brake (parking brake) lever is engaged, the unit is grounded by the chassis. !1 Clip Connector Car chassis q Attach a Clip Connector !1 to the end of the side brake (parking brake) connection lead. Comes up to this point. w The Clip Connector !1 is connected to the power source side lead of the side brake (parking brake) lever. Side Brake (Parking Brake) Connection Lead (Bright green) Power source side lead CQ-VD7003N English 8 9 Electrical Connections English 9 Wiring Diagram Caution ¡Check the connectors provided on your car (see precaution below) before connecting the system. ¡This unit is designed for use in a car having a 12 V negative ground battery system. ¡To prevent damage to the unit, be sure to follow the connection diagram. ¡Strip about 5 mm of the lead ends for connection (only non-ISO connector cords). ¡Do not insert the power connector into the unit until the wiring is completed. ¡Be sure to insulate any exposed wires to prevent short circuiting with the car chassis. Bundle all cables, and prevent cable terminals from touching any metal parts. ¡Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may clear the memory. ¡Run the cords avoiding the spots where the temperature can be extremely high. Precautions (ISO Connector) ¡The pin arrangement of the power connector conforms to ISO standard. [. . . ] This lead is not intended for use with a switch actuated power antenna. Note: ¡The power antenna extends automatically when the power of this unit is turned on. Head unit/Expansion Module Connecting cable (Supplied with CY-EM100N) (Video) (Yellow) (L) (White) (R) (Red) VIDEO OUT AUDIO OUT System-up Connector (R) (Red) (L) (White) (Video) (Yellow) Camcorder (option) Expansion Module CY-EM100N (option) DVD Changer CQ-VD7003N (Rear) AV2-IN CX-DH801N (option) (Video) (Yellow) RCA cord (option) VIDEO OUT VIDEO-CNT iPod (Video) (Yellow) (L) (White) CHANGER IN (R) (Red) Conversion Cable for DVD/CD Changer (CACC30N, option) Direct Cable for iPod (CA-DC300N, option) 16 CQ-VD7003N Connection with Rear View Camera Note: ¡Refer to the operating instructions for the connected devices, in addition. CQ-VD7003N (Rear) Camera Input Rear View Camera Control Unit (option) Rear View Camera (option) Panasonic (Video) (Yellow) RCA Cord (option) CAMERA-IN Camera Input Terminal (Yellow) (Video) (Yellow) Reverse lamp Clip connector (option) Battery REVERSE Car chassis P Reverse Lead (Violet/white stripe) !2 Reverse Extension Cord (Violet/white stripe) R N D 2 L Transmission gear Connecting the Reverse Lead If using an optional rear view camera, the reverse lead must be connected. [. . . ]