User manual PANASONIC CQ-VW100N

[. . . ] N'essayez pas de remplacer le fusible tout(e) seul(e). Zekering (15 A) Laat het vervangen van de zekering over aan uw dichtstbijzijnde Panasonic service-centrum. Probeer in geen geval zelf de zekering te vervangen. [. . . ] ¡Do not scratch the panel with fingernails or any hard objects. a Failure to observe the above may damage or break the glass on the surface of the touch panel. Installation Hardware (For Wiring) No. u Item Power Connector (ISO connector) Diagram Qty. 1 <YAJ024C128CA> i ISO Antenna Adapter 1 <YEAA33144> Note: ¡The number in parenthesis underneath each accessory part name is the part number for maintenance and service. ¡Accessories and their parts numbers are subject to modification without prior notice due to improvements. ¡Mounting Collar w is mounted on the main unit at shipment. ¡Use the supplied screws for installation exclusively. In case of losing any of them, please order the specific screw. CQ-VW100N English 4 5 Installation English 5 (continued) Mounting and removing the Main Unit Mounting Procedures (A) (When using Mounting Collar w) Note: ¡The car model, installation conditions and combination of the units used may impose some restrictions on opening and closing the monitor as well as on the angle and position to which the monitor can be adjusted. IMPORTANT When this unit is installed in dashboard, ensure that there is sufficient air flow around the unit to prevent damage from overheating. Do not block any ventilation holes on the unit. q Insert the Mounting Collar w into the dash- q board, and bend the mounting tabs out with a screwdriver. w Establish the rear connection of the unit. After fixing Power Connector u, fix the rear of the unit to the car body by either method (a) or (b). e Insert the unit into Mounting Collar w. Secure the clamp plate of Mounting Collar w to the hook. w e r t Snapping point r Insert Trim Plate q. t After installation reconnect the negative (­) battery terminal. Method for Fixing the Rear of the Unit (a) Using the Rear Support Strap (option) Fire wall of car (b) Using the Rubber Cushion (option) Rubber Bushing (option) Rear Support Bracket (Provided on the Car) To the unit r Mounting Bolt (5 mmø) 3 mmø Rear Support Strap (option, YEFG044C002) Tapping Screw (5 mmø x 16 mm) (option, XTT5+16AFN) Hex. Nut (5 mmø) (option, YEJN99023) To the unit r Mounting Bolt (5 mmø) 6 CQ-VW100N Mounting Procedures (B) (When not using Mounting Collar w) Use the brackets supplied with your car when mounting this unit. The bracket shape and mounting method vary with car manufacturers, car types and manufacturing year. ¡Run the cords avoiding the spots where the temperature can be extremely high. Precautions (ISO Connector) ¡The pin arrangement of the power connector conforms to ISO standard. ¡The pin arrangement of ISO connectors in some cars may differ from the ISO standard. ¡Please check that the pin arrangement of the connector in your car conforms to ISO standard. ¡For car types A and B, change the wiring of the red and yellow leads as shown at below. ¡After connection, insulate the portions marked () with insulating tape. Note: ¡For cars other than types A and B, please consult your local car shop. ISO Standard ISO () A7: IGN or ACC 12 V supply (Red) A7 (Red) ACC BATTERY 15A (Yellow) () (Yellow) A4 A4: 12 V Batteries (Continuous supply) A Car Type A (Red) () A7: 12 V Batteries (Continuous supply) (Yellow) BATTERY 15A ACC (Yellow) () (Red) A4: IGN or ACC 12 V supply B Car Type B (Red) () A7: 12 V Batteries (Continuous supply) (Red) ACC BATTERY 15A (Yellow) () (Yellow) A4: No connection Note: ¡To prevent from damage to the unit, be sure to follow the wiring diagrams at right. [. . . ] Head unit/Expansion Module Connecting cable (Supplied with CY-EM100N) (Video) (Yellow) (L) (White) (R) (Red) VIDEO OUT AUDIO OUT System-up Connector (R) (Red) (L) (White) (Video) (Yellow) CQ-VW100N (Rear) Camcorder Expansion Module CY-EM100N (option) DVD Changer CX-DH801N (option) Video Input Terminal (EXT VIDEO IN) (Video) (Yellow) VIDEO OUT RCA cord (option) iPod VIDEO-CNT (Video) (Yellow) (L) (White) CHANGER IN (R) (Red) Conversion Cable for DVD/CD Changer (CA-CC30N, option) Direct Cable for iPod with Video (CA-VDC300N, option) CQ-VW100N English 14 EXT VIDEO IN 15 Electrical Connections English 15 (continued) Connection with Rear Monitor Note: ¡Refer to the operating instructions for the connected devices, in addition. ¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in order to establish a proper connection. STAND BY (R) ON (G) COLOR LCD MONITOR Caution Rear Monitor ¡For people sitting in the front seats, please enjoy only audio during driving. Panasonic VM1500 Example: Audio Right Audio Left Video Input CQ-VW100N (Rear) VIDEO OUT (Video) (Yellow) Video Output Terminal (VIDEO OUT) (Video) (Yellow) RCA Cord (option) Connection with VCR or Camcorder Note: ¡Refer to the operating instructions for the connected devices, in addition. ¡Please observe what shapes the connectors of the connecting devices are and where each of them is connected to in order to establish a proper connection. (L) (White) RCA Cord (option) (L) (White) (R) (Red) (Video) (Yellow) Video Output Audio Left Audio Right INTELLIGENT SYSTEM (R) (Red) (Video) (Yellow) Example: POWER BS G-CODE CQ-VW100N (Rear) Camcorder VCR 16 CQ-VW100N Connection with Rear View Camera Note: ¡Refer to the operating instructions for the connected devices, in addition. [. . . ]