User manual PANASONIC CR-SRF100

[. . . ] Sirius Satellite Radio CR-SRF100 CR-SRT100 Operating Instructions CR-SRF100 (SHOWN) The contents of this manual are subject to change without notice and do not constitute a commitment on the part of Matsushita Communication Industrial Corporation of USA (MCUSA). Every effort has been made to ensure the accuracy of this document. However, due to ongoing product improvements and revisions, MCUSA cannot guarantee the accuracy of printed material after the date of publication, nor can it accept responsibility for errors or omissions. MCUSA will update and revise this document as necessary. [. . . ] Therefore, in this manual, "press a key" actually means "press and release a key" unless the operation happens after an extended key press (e. g. , storing a value in a preset) and then the manual will indicate "press and hold". SCROLLING INFORMATION When the length of the information to display is greater than the allocated space, the information will scroll across the screen one time and then a shortened version that does not scroll will appear. "CHANNEL NAME" SCREEN DISPLAY FORMAT (this is also called the "DEFAULT" screen display format) The channel name (default) screen display format is as follows · 1st line: Channel number & Channel Name · 2nd line: Category for the current channel being played EXAMPLE: The channel number is displayed in the first four characters of the top line, three digits and a trailing space. 22 CR-SRF100/CR-SRT100 The channel name is displayed in the last 12 characters of the top line. If the full channel name is greater than twelve characters in length, then the full channel name is scrolled across the display once, and the eight-character abbreviated version is displayed thereafter. The category name is displayed on the bottom line. If no category information accompanies this channel, then this area of the display area will be blank. If you change channels, there can be a slight delay in getting the new information to display. During a channel change, the new channel number is immediately displayed, and the rest of the display is updated when the new information is available. "PDT" SCREEN DISPLAY FORMAT . . . CHANGING TEXT INFORMATION BEING DISPLAYED Program Descriptive Text (PDT) is available in any of the principle modes of operation (other than SETUP). This information is only displayed on the second line of the display. The first line continues to display the channel number and category name. The screen display format is as follows · 1st line: Channel number & Channel Name · 2nd line: Category name OR PDT information for the specific program When the operator presses the [SEL] button, the type of information displayed on 2nd line rotates between the channel name and different types of PDT information. For example, if the · channel number is: 7 · category name is: "POP" · channel name is: "I-70" Then the available PDT data could be: · Artist Name "The Police" · Song Title "Roxanne" The PDT type ("ARTIST" or "TITLE") is temporarily displayed on the second line immediately before the PDT is displayed. CR-SRF100/CR-SRT100 23 Then pressing and releasing the [SEL] button will have the following effect: followed shortly by: 24 CR-SRF100/CR-SRT100 And repeated pressing of the [SEL] button will have the following effect: followed shortly by: CR-SRF100/CR-SRT100 25 The display reverts to: If the ARTIST or TITLE information is not available, the words "ARTIST" and "TITLE" are remain in their place. If a PDT field other than ARTIST and TITLE does not contain information the field is skipped and the next field that contains data is displayed. DISPLAY WHEN TUNING TO A CHANNEL STORED IN A PRESET No matter what mode you are in (PRESET, CHANNEL or CATEGORY), if you tune to a channel that is also stored in a preset (rotating the [SEL] knob OR pressing preset buttons [1] ­ [6]), the system momentarily displays the preset number and group on the lower line of the display before continuing with the pre-selected display format. If the channel selected is stored in multiple presets: · If the channel was selected by pressing a preset button [1] ­ [6] then that preset number & group are momentarily displayed. · If the channel was selected by any other means (e. g. , rotating the [SEL] knob) then the system will momentarily display the first preset number & group that the channel is stored in. 26 CR-SRF100/CR-SRT100 (STORING CHANNELS IN PRESETS To store a channel in a preset, press and hold the preset button for 2 seconds. The receiver will emit a short beep, indicating the channel is stored at that preset button in the current preset group. RECALLING PRESET CHANNELS If the user presses and releases a preset button [1] ­ [6] the system will select the channel stored at the preset number for the current preset group. CR-SRF100/CR-SRT100 27 7. 4. Category Mode The Sirius satellite system collects category information about each available channel. Any given channel may be associated with zero, one, or more than one category. Therefore a category map is constructed with each category identified with the specific channels associated with it. This channel and category mapping can be illustrated as: Category 1 (ex: "Rock") --------Channel 1 Channel 2 Channel 4 Channel 6 Channel 11 Channel 13 Channel 33 Channel 45 Category 1 (ex: "Jazz") --------Channel 3 Channel 5 Channel 7 Channel 6 Channel 12 Channel 16 Channel 33 Channel 58 Category 1 (ex: "Country") --------Channel 8 Channel 9 Channel 10 Channel 13 Channel 15 Channel 18 Channel 29 Channel 41 Channel 74 . . . Through the use of preset buttons or by being in channel mode, it is possible to tune to a channel not in the currently selected category. ENTERING CATEGORY MODE You enter category mode by pressing and releasing the [CATEGORY] button. The system indicates entering category mode by illuminating the category mode indicator located next to the category button. 28 CR-SRF100/CR-SRT100 EXITING FROM CATEGORY MODE You exit category mode by entering a different mode. · press the [CHANNEL] button to enter CHANNEL mode. · press the [PRESET] button to enter PRESET mode. [. . . ] This may be temporarily displayed if the user presses a key during the "SIRIUS SATELLITE RADIO" scrolling, and is not necessarily a problem. Action: If the message does not go away after approx. 6 seconds, check the electrical harness to the receiver. CR-SRF100/CR-SRT100 47 3. RECEIVER ERROR If communication between the receiver and CDU stops for approximately 6-9 seconds, then a "RECEIVER ERROR" message is displayed). Action: Check the electrical harness between the CDU and the receiver. 4. NO SUBSCRIPTION If the CDU determines that there is no subscription to the Sirius service, then the message "CALL 888539-SIRIUS TO SUBSCRIBE" will scroll twice on the display. [. . . ]