User manual PANASONIC CR-W200EU

[. . . ] Caution: To ensure safety, never attempt to preset stations while you are driving. Manual Station Preset CR-W200EU Press [BAND] to select a desired band. Use manual or seek tuning to find a station to be stored in the preset memory. Press and hold one of the preset buttons [1] to [6] until the display blinks once. Preset Number Note: You can change the memory setting by repeating the above procedure. CR-W200EU d d CR-W200EU Auto Station Preset CR-W200EU d Press and hold Select a band and press and hold [SCAN] (AUTO PRESETS) for more than 2 seconds. [. . . ] The 6 strongest available stations will be automatically saved in the memory on preset buttons [1] to [6]. Once set, the preset stations are sequentially scanned for 5 seconds each. Notes: In Auto Station Preset mode, only FM2 is available for FM stations. (FM1 is not available. ) Auto Station Preset is not activated in Weather Band. Any stations preset previously on the selected band will be erased. Tuning in a Preset Station CR-W200EU Press the corresponding preset buttons [1] to [6] to tune in a preset station. CR-W200EU 7 Tuning in a Weather Band Station Press any of the buttons [1] to [6] to monitor the preset station. CR-W200EU The frequency (162) remains unchanged. WB Weather Band Frequency Channel Number Note: The weather band (CH1-6) has been preset. j i Weather Band Stations National Weather Radio Broadcasts from over 380 locations throughout the U. S. Tune to weather band to receive continuous weather information 24 hours a day on one of the following frequencies. 162. 525 MHz Occasionally the frequency of an existing or planned station must be changed because of unexpected radio frequency interference with adjacent NOAA Weather Radio Stations and/or with other Government or Commercial Operations within the area. If you have a question concerning NOAA Weather Radio, please contact your nearest National Weather Service Office. 8 Clock Basics (The clock system is 12-hours. ) CR-W200EU Initial Time CR-W200EU Press and hold [CLK] to set time. Display blinks, and the time setting mode is activated. Note: Disconnect the cable from the negative (­) battery terminal. 1. Secure the Mounting Collar Insert Mounting Collar screwdriver. . into the vehicle's dashboard, and bend mounting tabs out with a Mounting Tab Dashboard 1 Mounting Collar Screwdriver 2. Secure the rear of the unit. a) Insert Power Connector to the unit. b) Check the electrical connection by referring to this operating instructions. c) Insert the unit into Mounting Collar and push it in until "click" is heard. 8 Power Connector Unit 12 To remove the unit from the vehicle's dashboard Insert each removal tool and pull. Removal tool (U-shaped) Note: Do not lose removal tools. They will be needed to remove the unit from the vehicle's dashboard. 13 Electrical Connections Cautions: This product is designed to operate with a 12-volt negative ground battery system. To prevent damage to the unit, be sure to follow the connection diagram below. Do not insert the power connector into the unit until the wiring is completed. Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and keep cable terminals free from touching any metal parts. Receiver CR-W200EU Antenna (Rear Side) Power Connector ACC (Red) Power Lead (ACC or IGN) To ACC power, +12V DC Ground (Black) Ground Lead To a clean, bare metallic part of the vehicle chassis Battery Lead To the vehicle battery, continuous +12V DC Dimmer Control Lead Connect to vehicle dimmer control lead Battery (Yellow) Dimmer (Gray w/black stripe) (White w/black stripe) (white) (Gray) (Green w/black stripe) (Orange w/White stripe) (Violet w/black stripe) (Green) (Violet) Left Speaker (Front) Right Speaker (Front) Left Speaker (Rear) Right Speaker (Rear) 14 Troubleshooting Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. [. . . ] Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and keep cable terminals free from touching any metal parts. Receiver CR-W200EU Antenna (Rear Side) Power Connector ACC (Red) Power Lead (ACC or IGN) To ACC power, +12V DC Ground (Black) Ground Lead To a clean, bare metallic part of the vehicle chassis Battery Lead To the vehicle battery, continuous +12V DC Dimmer Control Lead Connect to vehicle dimmer control lead Battery (Yellow) Dimmer (Gray w/black stripe) (White w/black stripe) (white) (Gray) (Green w/black stripe) (Orange w/White stripe) (Violet w/black stripe) (Green) (Violet) Left Speaker (Front) Right Speaker (Front) Left Speaker (Rear) Right Speaker (Rear) 14 Troubleshooting Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. Use a soft cloth for routine exterior cleaning. Never use benzine, thinner, or other solvent. When Something Doesn't Work Check the charts on page 16 for possible causes and solutions to any problem you might be experiencing. [. . . ]