User manual PANASONIC CR-W400U

[. . . ] VOL BASS TRE a a (Volume) (Treble) c d FADE CRW400U BAL b (Fader) (Balance) d Bass and Treble Press the knob to select the BASS or TREBLE mode and then turn it clockwise or counterclockwise to increase or decrease the bass/ treble level. -12 to 12 CRW400U -12 to 12 4 Power and Sound Controls (continued) Balance Press the knob to select the BALANCE mode and then turn it clockwise or counterclockwise to shift the sound volume to the right or left speakers. or L (R: Right, L: Left) 1 to 15 Balance Center Fader Press the knob to select the FADER mode and then turn it clockwise or counterclockwise to shift the sound volume to the front or rear speakers. or R 1 to 15 (F: Front, R: Rear) Fader Center Note: In the audio mode (BASS/TRE/BAL/FADE), the display will return to regular operation mode when there is no input for more than 5 seconds (2 seconds in the VOL mode). Press and hold Tone Enhancement (Loudness) Press and hold [BAND] (LOUD) for more than 2 seconds to enhance bass and treble tones when listening at low or medium volume. CRW400U Press and hold [BAND] (LOUD) for more than 2 seconds again to deactivate when listening at higher volumes. Mute Press [MUTE] to mute the sound completely. Press [MUTE] again to cancel. CRW400U 5 Radio Basics CRW400U Selecting a Band CRW400U Press [BAND] to change the band setting as follows. [. . . ] j (Hold [i] or [j] to change numbers rapidly. ) i j d Once the time has been set, release [CLK]. Note: When the clock is not set yet, "SET" is displayed. CRW400U CRW400U or Time Reset When you want to reset the time, repeat steps and above. CRW400U CRW400U CRW400U Clock Display Press [CLK] to display the current time. Press [CLK] again to return to previous display. CRW400U Note: The current time will be displayed at all the time even the power of the radio is turned off. 9 In Case of Malfunction Reset Switch If the unit does not respond when the function buttons are pressed, press the reset switch with a small pointed object, such as a pencil point. This will restore the unit to its default settings. All previously stored memory settings will be erased. Repeat the necessary steps in the previous pages to reprogram the clock and memory settings. If pressing the reset switch does not restore normal operation, please return the radio to the nearest authorized service center for CRW400U service. 10 Installation Guide WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers in attempting to install this product. Any attempt to install this product in a motor vehicle by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. Overview This equipment should be installed by a professional. However, if you plan to install this unit yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to "WARNING" statement above). Connect the vehicle wires to the wires of the power connector. [. . . ] Be sure to insulate any exposed wires from a possible short-circuit from the vehicle chassis. Bundle all cables and keep cable terminals free from touching any metal parts. Receiver CR-W400U Antenna (Rear Side) Power Connector ACC (Red) Power Lead (ACC or IGN) To ACC power, +12V DC Ground (Black) Ground Lead To a clean, bare metallic part of the vehicle chassis Battery Lead To the vehicle battery, continuous +12V DC Dimmer Control Lead Connect to vehicle dimmer control lead Battery (Yellow) Dimmer (Gray w/black stripe) (White w/black stripe) (white) (Gray) (Green w/black stripe) (Orange w/White stripe) (Violet w/black stripe) (Green) (Violet) Left Speaker (Front) Right Speaker (Front) Left Speaker (Rear) Right Speaker (Rear) 14 Troubleshooting Maintenance Your product is designed and manufactured to ensure a minimum of maintenance. [. . . ]